Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation of stupichny assembly of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major maintenance and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblies of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement of back stupichny bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assembly of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and installation of a steering wheel
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assembly of the switch of the ignition/lock of a steering column
   The steering mechanism - general information, removal, major maintenance and installation
   System of hydrostrengthening of a wheel - general information
   Removal and installation of tips of steering drafts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


Removal and installation of a stretcher of a forward suspension bracket

Removal

The divider of spherical support is required. Everything самоконтрящиеся nuts at assembly are subject to replacement without fail.


 PERFORMANCE ORDER

1. Dump pressure in hydraulic system (see. Head Uniform hydraulic system).
2. To Poddomkratta the car also establish it on props. Remove forward wheels.
3. Under the car remove a protective cover from a nut of the cranked lever of a drive of gear shifting, give a nut and disconnect draft of switching from the rotary support on a stretcher.

4. Turn out fastening boats to a stretcher of the mechanism of reechny steering transfer, remove remote plugs. A wire tie up assembly of the steering mechanism to system of production of the fulfilled gases.

5. Give a nut and take a bolt of fastening of an arm of a back support of the power unit to the rubber pillow.

6. From both parties of the car turn out bolts of fastening of loker of wheel arches to a stretcher.
7. Serially weaken and partially unscrew nuts of fingers of both bottom spherical support, then divide support by means of the special tool. After liberation of spherical fingers finally remove nuts from their shafts.
8. Operating in the same manner, by means of a divider of spherical support serially disconnect racks of the stabilizer of cross-section stability from the ends of its bar. At an otdavaniye of nuts the finger of a rack can be held from a provorachivaniye by means of a prutkovy key on 5.0 mm.
9. From the left board of the car weaken and partially unscrew a nut of a spherical finger of fastening of a tip of steering bent for to stupichny assembly. Liberate a finger from the landing nest by means of a divider of spherical support, then finally remove a nut.

10. In the right back corner of a stretcher turn out two bolts and release a clamp of fastening directing lines of communication (wires and hydraulic tubes). For an otpuskaniye of a clamp beat out its central pin.

11. On the models equipped with a hydroactive suspension bracket disconnect electroconducting from the sensor of movings of a body.

12. Turn out two bolts of fastening of klapanny assembly of the proof-reader of a road gleam to a stretcher.

13. Weaken a coupling bolt and disconnect from the proof-reader an executive rod of manual correction of a road gleam.

14. Disconnect from the valve of the proof-reader hydraulic tubes. At once закупорьте the open ends of lines and reception ports of the valve in order to avoid hit in dirt system.

15. Turn out three bolts of fastening of basic arms of lines of communication in the left back corner of a stretcher.

16. Take a fastening clamp on a stretcher directing lines of communication. For an otpuskaniye of a clamp beat out its central pin.

17. Disconnect tips of cables of a drive of the parking brake from executive levers of supports of brake mechanisms. Liberate covers of cables from bearing ledges on supports. Take assemblies of cables aside.
18. Since both ends of a stretcher liberate hydraulic tubes from basic arms (separate from tubes flexible hoses, then liberate tubes from intermediate clamps on a stretcher) (address to Head Brake system).
19. Turn a steering wheel against the stop to the left.
20. Attentively examine a stretcher and liberate from clamps on it all remained lines of communication (wires, hydraulic tubes and hoses (it is possible, it is necessary to make a detachment of some lines). Try to remember routes of laying of all wires, hoses and tubes. At a rassoyedineniye of shtutserny sockets be ready to collecting spilled liquid. At once cork the open ends of tubes/hoses and unions of their connection for the purpose of minimization of losses of hydraulic liquid and in order to avoid hit in dirt system.
21. Prop up a stretcher a telezhechny jack through wooden whetstone.

22. Turn out six fixing bolts and slightly lower a stretcher on a jack.



23. Last time make sure that no communication tenches disturb stretcher removal.
24. Finally lower a stretcher and take it from under the car.
25. At desire the bottom levers and a bar of the stabilizer of cross-section stability can be removed from a stretcher (see appropriate sections).

Installation

Installation is made upside-down. Pay attention to the next moments:
   a) Where it is required, establish on a stretcher the bottom levers and a bar of the stabilizer of cross-section stability of a suspension bracket according to the instructions provided in the sections Removal, major maintenance and installation of the bottom lever of a forward suspension bracket and Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket. Pay attention that the final tightening of fixture should be made only after stretcher installation on the car;
   b) At the corresponding complete set do not forget to replace sealing elements of shtutserny connections of hydraulic lines;
   c) Remember that everything самоконтрящиеся nuts are subject to replacement without fail;
   d) Track correctness of laying and reliability of fastening of all lines of communication;
   e) Do not forget to check correctness of adjustment of the parking brake (address to Head Brake system);
   f) After car lowering on the earth tighten spuskny the gate of a regulator of pressure and transfer a control lever a suspension bracket to the situation "Maximum";
   g) Check level of hydraulic liquid, in case of need make the corresponding adjustment (address to Head Routine maintenance);
   h) Do not forget to pump over hydraulic system (address to Head Brake system);
   i) In summary, make adjustment of height of a road gleam according to the instructions provided in the section Check of installation and adjustment of a road gleam, then tighten coupling bolts of collars of fastening of the proof-reader of a road gleam and (at the corresponding complete set) the sensor of movings of a body.