Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation of stupichny assembly of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major maintenance and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblies of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement of back stupichny bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assembly of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and installation of a steering wheel
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assembly of the switch of the ignition/lock of a steering column
   The steering mechanism - general information, removal, major maintenance and installation
   System of hydrostrengthening of a wheel - general information
   Removal and installation of tips of steering drafts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket

Stabilizer bar

Самоконтрящиеся “Nylock” nuts at assembly are subject to replacement without fail.

Removal


Details of fastening of the proof-reader of height of a road gleam

1 — the Coupling bolt of a collar of fastening on a bar of the stabilizer of the proof-reader
2 — the Coupling bolt of a collar of fastening on a bar of the stabilizer of the sensor of movings of a body
3 — the Point of a detachment of the sensor
4 — Bolts of fastening of a basic plate of the proof-reader
5 — a detachment Point from the proof-reader of the lever of manual adjustment of a road gleam


 PERFORMANCE ORDER

1. Dump pressure in hydraulic system (see. Head Uniform hydraulic system).
2. Prop up protivootkatny boots back wheels, then поддомкратьте a front of the car and establish it on props. Remove forward wheels.
3. Under the car remove a cap from a nut of the cranked lever of a drive of gear shifting, then give a nut and disconnect driving draft from an axis on a stretcher.
4. Turn out bolts of fastening of assembly of the steering mechanism on a stretcher, remove remote washers.
5. Turn out a coupling bolt of a collar of fastening of the proof-reader of height of provision of a suspension bracket on a bar of the stabilizer of cross-section stability.
6. On models with a hydroactive suspension bracket turn out a bolt of a collar of fastening to a bar of the sensor of moving of a body (see an illustration of the Detail of fastening of the proof-reader of height of a road gleam). Disconnect from the sensor the executive lever.
7. Turn out two bolts of fastening of a basic plate of the valve of the proof-reader of height of a suspension bracket to a stretcher (see an illustration of the Detail of fastening of the proof-reader of height of a road gleam).
8. Weaken a coupling bolt and disconnect the lever of manual adjustment of a road gleam from assembly of the proof-reader of height of a suspension bracket (see an illustration of the Detail of fastening of the proof-reader of height of a road gleam).
9. Having accurately hooked, liberate the plastic lever of the proof-reader of height of provision of a suspension bracket from the spherical hinge on the executive lever.
10. From both parties of a stretcher liberate brake tubes from basic arms (separate from a tube a flexible hose, then liberate a tube from clips on a stretcher) (address to Head Brake system).
11. Examine a stretcher and liberate from its clips all hydraulic lines and electroconducting plaits. Some of tubes/hoses should be disconnected. Try to remember routes of laying of lines of communication, prepare for collecting spilled fuel. The open ends of the disconnected lines and their unions at once закупорьте for the purpose of minimization of losses of liquid and in order to avoid hit in dirt system.

12. Give boltovy connection of fastening of an arm of a back support of the power unit to a rubber pillow.

13. From both parties of a stretcher turn out bolts of fastening of loker of wheel arches to it.
14. In the right back corner of a stretcher turn out two bolts and remove a collar of fastening directing wires/tubes. For removal of a collar beat out the central finger.
15. Turn out three bolts of fastening of basic arms of plaits of electroconductings/tubes in the left back corner of a stretcher.
16. Remove a collar of fastening directing lines of communication in the left back corner of a stretcher (for removal of a collar beat out the central finger).
17. Disconnect from the ends of a bar of the stabilizer its basic racks (see subsection "Racks of the stabilizer of cross-section stability - Removal", item 2).
18. Once again make sure that nothing remained connected and does not disturb stretcher dismantle.
19. Turn out back bolts of fastening to a stretcher of the bottom levers of a suspension bracket. Pay attention that the most back serve also for fastening of collars of fastening of a bar of the stabilizer. Remove collars of fastening of a bar.
20. Prop up a stretcher a telezhechny jack through wooden pro-rates.
21. Turn out six fixing bolts and slightly lower a stretcher on a jack.
22. Remove rubber plugs of collars from a bar of the stabilizer of cross-section stability.

23. Lower a stretcher approximately on 100 mm and take a stabilizer bar from under the car.

Installation

Installation is made upside-down. Pay attention to the next moments:


Details of fastening of the bottom lever of a suspension bracket / fixing collar of a bar of the stabilizer of cross-section stability

And — the Control size
1 — the Collar of fastening of a bar
2 — the Fixing bolt

     a) Arrange a bar of the stabilizer of cross-section stability so that the size (And) (see an illustration of the Detail of fastening of the bottom lever of a suspension bracket / a fixing collar of a bar of the stabilizer of cross-section stability) between fixing openings of a rack and the bottom surface of a stretcher made 21 ± 2 mm, then tighten bolts of fastening of the bottom levers/collars of fastening of a bar;
   b) Do not tighten a collar of fastening of the proof-reader of height of provision of a suspension bracket and the sensor of movings of a body until the size of a road gleam will be adjusted;
   c) Do not forget to replace everything самоконтрящиеся a nut;
   d) All fixture tighten with demanded effort;
   e) Track correctness of laying and reliability of fastening of lines of communication where it is required, replace sealing couplings of shtutserny sockets;
   f) After car lowering on the earth tighten spuskny the gate of a regulator of pressure and transfer a control lever a suspension bracket to the situation "Maximum" (see. Head Uniform hydraulic system);
   g) Check liquid level in the tank of hydraulic system, in case of need make the corresponding adjustment (address to Head Routine maintenance);
   h) Pump over brake system (address to Head Brake system);
   i) In summary check adjustment of height of a road gleam (see. Check of installation and adjustment of a road gleam), then tighten collars of fastening of the proof-reader and (at the corresponding complete set) the sensor of movings of a body.

Racks of the stabilizer of cross-section stability

New fixing nuts be required.

Removal

 PERFORMANCE ORDER

1. Prop up protivootkatny boots back wheels of the car, then поддомкратьте a front of the car and establish it on props. Remove the corresponding forward wheel.
2. Partially weaken a nut of fastening of a rack of the stabilizer on the end of its bar. Disconnect a bar from a rack by means of a divider of spherical support, then finally remove a nut.

At a nut otdavaniye the finger of a rack can be held from a provorachivaniye by means of a prutkovy key on 5.0 mm.

3. Give a fixing nut and disconnect a stabilizer rack from a suspension bracket rack (for finger keeping from a provorachivaniye, as before, use a prutkovy key on 5.0 mm). In case of need use a divider of spherical support, however do not forget to screw before thus a nut for the end of a carving part of a finger not to damage carving rounds.

4. Remove a rack of the stabilizer of cross-section stability from the car.

Installation

Installation is made upside-down. Do not forget to replace fixing nuts. Track observance of demanded efforts of a tightening of fixture.