Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation of stupichny assembly of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major maintenance and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblies of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement of back stupichny bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assembly of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and installation of a steering wheel
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assembly of the switch of the ignition/lock of a steering column
   The steering mechanism - general information, removal, major maintenance and installation
   System of hydrostrengthening of a wheel - general information
   Removal and installation of tips of steering drafts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


Removal and installation of assembly of the back bridge

Removal

At the corresponding complete set prepare new sealing couplings of shtutserny sockets of hydraulic tubes.


 PERFORMANCE ORDER

1. Dump pressure in hydraulic system (see. Head Uniform hydraulic system).
2. Prop up protivootkatny boots forward wheels, firmly cock the parking brake, then поддомкратьте a back of the car and establish it on props. Remove back wheels.
3. Remove a spare wheel with an arm of its fastening under the car.

4. Turn out fixing bolts and remove a connecting bar from assembly of the back bridge.

5. Remove back and intermediate sections of system of production of the fulfilled gases (see. Systems of decrease in toxicity and production of the fulfilled gases).
6. Weaken a coupling bolt and disconnect an executive rod of manual adjustment of a road gleam from assembly of the hydraulic proof-reader.
7. On the models equipped with a hydroactive suspension bracket, disconnect the sensor of movings of a body.
8. On models with ABS disconnect electroconducting from wheel sensors.
9. Disconnect tubes of giving and liquid return from assembly of the hydraulic regulator established in the central part of the back bridge. Prepare for collecting spilled liquid, at once закупорьте the open ends of lines and unions of their connection for the purpose of minimization of losses of hydraulic liquid and in order to avoid hit in dirt system.

10. Examine assembly of the bridge and liberate from intermediate clamps all hydraulic and electric lines of communication disturbing to further dismantle of the bridge. Some of lines should be disconnected. Try to remember routes of laying of all wires, tubes and hoses. The open ends of lines at once закупорьте in order to avoid hit in dirt system.

11. Disconnect tubes of gasoline pipe lines from a fuel tank and liberate them from intermediate clamps on the car bottom.
12. Prop up assembly of the back bridge by a jack through wooden whetstone. Track, that the emphasis fell on bearing lateral beams.

13. Turn out four bolts of fastening of assembly of the back bridge.
Above — the Forward bolt of fastening of assembly of the back bridge
Below — the Back bolt of fastening of assembly of the back bridge



14. Slightly omit assembly on a jack.
15. Last time make sure, no communication tenches remained connected.
16. Slightly submit bridge assembly back for the purpose of an obvedeniye of a jellied mouth of a fuel tank.
17. Omit bridge assembly on a jack and take it from under the car.

Installation

Installation is made upside-down. Pay attention to the next moments:
   a) Track correctness of laying and reliability of fastening of all lines of communication;
   b) At the corresponding complete set replace sealing elements of shtutserny sockets of hydraulic tubes;
   c) All fixture tighten with demanded effort;
   d) Tighten spuskny the gate of a regulator of pressure and transfer a control lever a suspension bracket to the situation "Maximum";
   e) In summary pump over brake system (address to Head Brake system).