Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation of stupichny assembly of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major maintenance and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblies of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement of back stupichny bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assembly of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and installation of a steering wheel
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assembly of the switch of the ignition/lock of a steering column
   The steering mechanism - general information, removal, major maintenance and installation
   System of hydrostrengthening of a wheel - general information
   Removal and installation of tips of steering drafts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


Removal and installation of stupichny assembly of a forward suspension bracket

The divider of spherical support and new nuts of spherical fingers be required.

Removal

 PERFORMANCE ORDER

1. Dump pressure in hydraulic system (see. Head Uniform hydraulic system).

2. Prop up protivootkatny boots back wheels, поддомкратьте a front of the car and establish it on props. Remove the corresponding forward wheel. Whenever possible, weakening of a nut of fastening of a power shaft should be made to a car poddomkrachivaniye:
   a) Prop up protivootkatny boots forward wheels and remove decorative caps of rims;
   b) Firmly cock the parking brake;
   c) Take a R-shaped clamp and remove a lock cap of a nut;
   d) Weaken a nut by means of a suitable face key.



3. Weaken and partially unscrew a nut of a spherical finger of a tip of steering draft on stupichny assembly (unscrew a nut till the end of a carving for the purpose of protection of rounds by the last at hinge liberation). Liberate a sharovy finger of a tip from stupichny assembly by means of a divider of spherical support, then finally remove a nut.

4. To Otboltita from a rack also shift aside a basic arm elektroprovodki/a hydraulic hose.

5. Remove a brake disk (address to Head Brake system). Weaken and partially unscrew a nut of a finger of the bottom spherical support (unscrew a nut till the end of a carving fingers for the purpose of protection of rounds by the last at hinge liberation). Liberate a sharovy finger from stupichny assembly by means of a divider of spherical support, then finally remove a nut.
6. Liberate the external end of a power shaft from stupichny assembly (see. Head Power shafts). Pay attention to the next moments:
   a) There is no need to merge transmission oil from a transmission;
   b) Do not liberate an internal pin of a power shaft from transmission, and at work from the right board of the car do not liberate also intermediate bearing of a shaft;
   c) A wire tie up the free external end of a power shaft to a suspension bracket element.

7. Give a nut of a coupling bolt of a collar of fastening of stupichny assembly on a suspension bracket rack.

8. By means of a prutkovy key on 8.0 mm dissolve a groove of a collar of fastening of stupichny assembly on suspension brackets (enter a six-sided prutok into a groove and turn it on a turn quarter). At the same time omit stupichny assembly down, removing it from a rack.

Installation

 PERFORMANCE ORDER

1. Dissolve a collar of fastening of stupichny assembly by means of a prutkovy key (see the previous subsection, the last point).
2. Put on stupichny assembly a suspension bracket rack (the directing ledge on a rack should get a collar groove).
3. Push a nave up on a rack against the stop it in bearing coat hanger.
4. Establish a coupling bolt (a bolt it is necessary to fill in a collar in front), screw a new nut and tighten it with demanded effort.
5. Establish into place a brake disk and a support, connect a cable of a drive of the parking brake (address to Head Brake system).
6. Fill in a nave a pin of a power shaft, screw and tighten a fixing nut (see. Head Power shafts). Whenever possible the nut should be tightened after car lowering on the earth.
7. Establish on a suspension bracket rack bearing arm elektroprovodki/a hydraulic hose and fix it two bolts.
8. Connect to stupichny assembly a tip of steering draft, having fixed a sharovy finger a new nut. Tighten a nut of a spherical finger with demanded effort.
9. Establish into place a wheel, then lower the car on the earth and tighten wheel (and stupichny) nuts with demanded effort.
10. Tighten spuskny the gate of a regulator of pressure and transfer a control lever a suspension bracket to the situation "Maximum".
11. In summary make adjustment of corners of installation of forward wheels (see. Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels).