Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation of stupichny assembly of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major maintenance and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblies of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement of back stupichny bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assembly of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and installation of a steering wheel
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assembly of the switch of the ignition/lock of a steering column
   The steering mechanism - general information, removal, major maintenance and installation
   System of hydrostrengthening of a wheel - general information
   Removal and installation of tips of steering drafts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


Running gear and steering

Specifications

Corners of installation of forward wheels

Convergence, mm

0 ÷ 30 (0°00 '÷ 0°00') divergence

Corner of a longitudinal inclination of an axis of turn of a wheel (выбег)

   •  Models with a manual drive of the steering mechanism

1 °

   •  The models equipped with system of hydrostrengthening of a wheel

3 °

Disorder (to adjustment is not subject)

0°00' ± 30 °

Corner of a cross-section inclination of an axis of turn of a wheel (to adjustment is not subject)

13°20'

Corners of installation of back wheels

Convergence, mm (to adjustment is not subject)

1.0 ÷ 6.0 (0°10 '÷ 0°50')

Disorder

1°15' ± 20 ° (negative)

Road gleam

Height of a road gleam of a front of the car, mm

155.0 +7, 155.0-10

Height of a road gleam of a back of the car, mm

420.0 +7, 420.0-10

Suspension bracket of forward wheels

Diameter of the stabilizer of cross-section stability, mm

All models, except equipped with the RFY series engine (16 valves)

22.0

The models equipped with the engine of the RFY series

23.0

Pressure of gas in spherical receivers, a bar

Except the models equipped with the engine of the RFY series

70 +5, 70-20

The models equipped with the engine of the RFY series

55 +5, 55-20

Models with a hydraulic suspension bracket

   •  Models of 2.0 l (with 8-клапанными engines)

50 +5, 50-20

   •  Models with 16-klapanny engines (RFY)

70 +5, 70-20

Volume of spherical receivers of a hydraulic suspension bracket, cm 3

400

Volume of additional spherical receivers of a suspension bracket (hydroactive suspension bracket), cm 3

500

Diameter of the cylinder of a hydraulic actuator of a suspension bracket, mm

40.0

Suspension bracket of back wheels

Diameter of the stabilizer of cross-section stability, mm

All models, except equipped with the RFY series engine (16 valves)

21.0

The models equipped with the engine of the RFY series

22.0

Pressure of gas in spherical receivers, a bar

Except the models equipped with the engine of the RFY series

40 +5, 40-10

The models equipped with the engine of the RFY series

30 +5, 30-10

Models with a hydraulic suspension bracket

   •  Models of 2.0 l (with 8-клапанными engines)

30 +5, 30-10

   •  Models with 16-klapanny engines (RFY)

50 +5, 50-20

Volume of spherical receivers of a hydraulic suspension bracket, cm 3

400

Volume of additional spherical receivers of a suspension bracket (hydroactive suspension bracket), cm 3

500

Diameter of the cylinder of a hydraulic actuator of a suspension bracket, mm

35.0

Steering drive

Number of turns of a steering wheel

Models with a manual drive of the steering mechanism

34

The models equipped with system of hydrostrengthening of a wheel

Except the cars equipped with the engine of the RFY series

4.6

The cars equipped with the engine of the RFY series (16 valves)

3.2

Design of the steering mechanism

Reechny

Number of teeths of a steering rack

Models with a manual drive of the steering mechanism

6

The models equipped with system of hydrostrengthening of a wheel

8

Transfer number of reechny transfer

Models with a manual drive of the steering mechanism

24.5:1

The models equipped with system of hydrostrengthening of a wheel

17.0:1

Efforts of a tightening of carving connections, Nanometer

Forward suspension bracket

Nut of fastening of a power shaft

320

Nut of a coupling bolt of a collar of fastening of stupichny assembly to a suspension bracket rack

54

Nut of fastening of the bottom spherical support to the bottom lever of a suspension bracket

45

Fastening of a spherical support of the bottom lever to stupichny assembly

250

Nuts of fastening of racks of the stabilizer of cross-section stability

   •  Nuts М10

40

   •  Nuts М12

70

Back nuts of fastening of the bottom lever of a suspension bracket (and collars of a bar of the stabilizer of cross-section stability)

85

Nut of an axial bog of the bottom lever of a suspension bracket

85

Bolts of fastening of the hydraulic block on a body

25

Nut of fastening of a rack of a suspension bracket to the hydraulic block *

45

Screws of fastening of a hydraulic regulator

8

Bolts of fastening of a forward stretcher

120

Back suspension bracket

Stupichny nut

280

Bolts of fastening of the stabilizer of cross-section stability to longitudinal levers of a suspension bracket

95

Nut of an axis of the longitudinal lever

130

Bolts of fastening of a connecting bar

28

Forward bolts of fastening of a back suspension bracket

80

Back bolts of fastening of a back suspension bracket

110

Nuts of fastening of a rubber pillow of a back support of a suspension bracket to a body

280

Screws of fastening of a hydraulic regulator

8

Steering

Nut of a steering wheel

30

Nut of the spherical hinge of a tip of steering draft

35

Coupling bolt of the kardanny hinge of a steering column

20

Nuts of a steering column

15

Coupling bolt of fastening of an intermediate shaft of a steering column to a gear wheel of the steering mechanism

20

Bolts of fastening of a case of the steering mechanism to a stretcher

70

Lock-nut of a tip of steering draft

45

Fastening of a tip of steering bent for to the reechny mechanism

60

Shtutsernye sockets of hydraulic lines

   •  Tubes in diameter of 3.5 ÷ 4.5 mm

8

   •  Tubes in diameter of 6.35 mm

      ••  With the sealing coupling

10

      ••  Without the sealing coupling

13

   •  Tubes in diameter of 10 mm

30

Wheels

Bolts of fastening of wheels

90

* hermetic application for fixing of carving connections Is required.

General information


Function chart of a hydroactive suspension bracket

1 — the Left forward spherical receiver
2 — the Additional forward spherical receiver
3 — the Forward regulator of pressure
4 — the Left back spherical receiver
5 — the Additional back spherical receiver
6 — the Back regulator of pressure

7 — the Right back spherical receiver
8 — the Proof-reader of height of provision of a back suspension bracket
9 — the Filter
10 — the Safety valve
11 — the Right forward spherical receiver

On models of cars considered in the real Management the independent suspension bracket of hydropneumatic type of an exclusive design of Citroёn is used.

The main components of a forward suspension bracket are vertically established hydraulic rack, the bottom levers and a bar of the stabilizer of cross-section stability. The bottom levers and a bar of the stabilizer of cross-section stability are established on a forward stretcher of the car. Supply of working liquid in hydraulic blocks is carried out from the main hydraulic system of the car through the proof-reader of height of provision of the forward suspension bracket, influencing a bar of the stabilizer of the cross-section stability, attached to the bottom levers of a suspension bracket by means of racks.

Longitudinal levers, and also the back hydraulic blocks (racks) supplied by working liquid from the main system through the proof-reader of height of provision of a back suspension bracket are put in a basis of a design of a back suspension bracket.

The height of a road gleam of the car can change by switching of the car of a control lever established in salon. The lever is connected by means of executive rods to proof-readers of height of a lobby and a back suspension bracket. On models of early years of release at engine switching off the car falls to the bottom situation. Later models are equipped with the unilateral valve isolating a suspension bracket from the main hydraulic system that allows to avoid similar lowering of a body after останова the engine.

Hydraulic blocks are equipped with the automatic dampers replacing screw springs and assemblies of shock-absorbers, used in suspension brackets of usual type.

Some of models of a representation class are equipped with the special "hydroactive" suspension bracket allowing the driver to choose one of two modes of installation of a suspension bracket ("Normal" or "Sports"). The system has electronic control on the basis of signals established on elements of a suspension bracket of information sensors. "Normal" installation provides the maximum comfort at car movement, automatically adapting a suspension bracket for a manner of driving of the driver and a paving condition. At a choice of the "Sports" mode the suspension bracket becomes more rigid that is suitable for a sports manner of driving and at movement on a serpentine more. The function chart of a hydroactive suspension bracket is given in an illustration the Function chart of a hydroactive suspension bracket.

The steering mechanism of reechny type is established on the cross-section beam attached to a stretcher. The steering rack is equipped with the kardanny hinge and the flexible coupling. Some of models are equipped with system of hydrostrengthening of a wheel working liquid in which moves from a path of the main hydraulic system of the car (see. Head Uniform hydraulic system).