Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation of stupichny assembly of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major maintenance and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblies of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement of back stupichny bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assembly of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and installation of a steering wheel
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assembly of the switch of the ignition/lock of a steering column
   The steering mechanism - general information, removal, major maintenance and installation
   System of hydrostrengthening of a wheel - general information
   Removal and installation of tips of steering drafts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


Removal and installation of longitudinal levers of a back suspension bracket

Removal

The new nut of an axis of the rotary lever is required.


 PERFORMANCE ORDER

1. Prop up protivootkatny boots forward wheels and cock the parking brake, then поддомкратьте a back of the car and establish it on props. Remove the corresponding back wheel.
2. Remove the corresponding hydraulic block of a back suspension bracket (see. Removal and installation of hydraulic blocks of a back suspension bracket).

3. On the equipped ABS models execute the following procedures:
   a) Turn out three fixing screws and remove a brake board;
   b) Turn out a fixing bolt and remove the wheel ABS sensor. Shift the sensor aside, watching that it did not appear its electroconducting is tense;
   c) Remove the thermofilter of the wheel sensor.

4. Release the shtutserny socket and disconnect from a brake support a hydraulic tube. At once закупорьте the open ends of a tube and the union of its connection in order to avoid hit in dirt system.
5. Liberate hydraulic tubes from intermediate clamps on the longitudinal lever and assembly of the back bridge.
6. Get a jack under located from an opposite board of the car the longitudinal lever and cock it so that the lever appeared is parallel to the earth.

7. Turn out two bolts of fastening to subject removal to the longitudinal lever of a bar of the stabilizer of cross-section stability. Pay attention that one of bolts is used also for fastening of a basic arm of a hydraulic tube.

8. Give a nut of an axis of the rotary lever.

9. Get wooden whetstone between a bar of the stabilizer of cross-section stability and a car body, then use it as the lever for bar assignment from a body. Try not to allow tension of the hydraulic tubes fixed in arms over the end of a bar of the stabilizer.
10. Take an axis of the longitudinal lever, then remove from the car the lever.

Installation

Installation is made upside-down. Pay attention to the next moments:
   a) Before installation it is necessary to grease an axis of the longitudinal lever on all length;
   b) Do not forget to replace a nut of an axis of the lever. Track observance of efforts of a tightening of fixture;
   c) The description of procedure of installation of the hydraulic block is provided in the section Removal and installation of hydraulic blocks of a back suspension bracket;
   d) In summary do not forget to pump over hydraulic system (address to Head Brake system).