Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation of stupichny assembly of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major maintenance and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblies of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement of back stupichny bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assembly of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and installation of a steering wheel
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assembly of the switch of the ignition/lock of a steering column
   The steering mechanism - general information, removal, major maintenance and installation
   System of hydrostrengthening of a wheel - general information
   Removal and installation of tips of steering drafts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes



Replacement of bearings of forward naves

2-рядные roller stupichny bearings have a tight design. Adjustment of a pretightness and stuffing of bearings by greasing is made at manufacturer. Bearings are calculated on all service life of the car and additional service do not need. Try not to allow pullings of nuts of fastening of power shafts above admissible value.


For performance of procedure the suitable press, or the workbench equipped with a big vice is required. Prepare also suitable opravka (face heads of the corresponding size will approach). Internal holders of bearings are put in a nave внатяг and sometimes act in film together with a nave. In such cases for their extraction it is necessary to use a special stripper of lezviyny type.


 PERFORMANCE ORDER

1. Remove stupichny assembly (see. Removal and installation of stupichny assembly of a forward suspension bracket).
2. Strongly lay stupichny assembly on pair of wooden blocks, or clamp it in a vice with soft sponges. Rest an opravka suitable on the size against an internal end face of a flange of stupichny assembly, pull together a flange from the bearing. If the external part of an internal holder of the bearing remains in a nave, use for its extraction by a stripper (see the prevention at the beginning of the section).

3. Remove a lock ring of the bearing from an external end face of stupichny assembly.

4. In case of need plant an internal holder of the bearing back on a separator and strongly prop up inside of stupichny assembly. By means of an opravka suitable on the size выпрессуйте the bearing from a nave (the opravka should rest only against an end face of an internal holder of the bearing).
5. Carefully wipe stupichny assembly, заполируйте teases and the acting edges, capable to prevent installation of components. Check assembly on existence of cracks and other mechanical damages, in case of need replace defective components.

The lock ring of the bearing is subject to replacement without fail, regardless of its condition.

6. Slightly oil an external holder of the bearing and an axis of a flange of a nave.
7. Reliably prop up stupichny assembly and plant in it the bearing. Track perpendicularity of landing of the bearing. Opravka should rest only against a face surface of an external holder.
8. Having planted the bearing, fix it a new lock ring, having tracked correctness of landing of the last in the flute in stupichny assembly.
9. Prop up the outer side of stupichny assembly and with plant an internal holder of the bearing on a pin of a flange of a nave. Press the bearing against the stop in bearing coat hanger by means of an opravka resting against an end face of an internal holder. Check freedom of rotation of a flange of a nave, remove excess of greasing.
10. Establish into place stupichny assembly (see. Removal and installation of stupichny assembly of a forward suspension bracket).