Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation of stupichny assembly of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major maintenance and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblies of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement of back stupichny bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assembly of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and installation of a steering wheel
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assembly of the switch of the ignition/lock of a steering column
   The steering mechanism - general information, removal, major maintenance and installation
   System of hydrostrengthening of a wheel - general information
   Removal and installation of tips of steering drafts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


Removal, check of a condition of components and installation of a steering column

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Establish forward wheels of the car in rectilinear situation.
3. Remove a steering wheel (see. Removal and installation of a steering wheel).
4. Remove casings of a steering column (address to Head the Body and salon furnish).

5. Release clamps / turn out fixing screws and remove the panel of furnish of a forward wall of a driver's foot well.

6. Turn out two fixing screws on the left side of the panel of the bottom cover of a casing of a steering column.

7. Turn out the remained three screws of fastening of the bottom cover of a column / the assembly block of safety locks. Access to screws opens through a casing of the assembly block. Remove the panel (at the corresponding complete set do not forget to disconnect from it electroconducting).
8. Under a steering column disconnect electroconducting from assemblies of the lock of ignition and the podrulevy switch.

9. In the lower part of a column turn out a coupling bolt of the kardanny hinge of a steering shaft.

10. Give four fixing nuts (do not forget about washers).
Above — Two bottom nuts
Below — Two top nuts



11. Remove assembly of a steering column.

Check

 PERFORMANCE ORDER

1. The steering column has the telescopic design considerably increasing injury prevention of the driver in case of failure. At front blow the steering shaft develops, considerably reducing rigidity of blow of the driver a breast about a steering wheel. Before column installation into place check it on existence of signs of deformations and mechanical damages of components, in case of need make the corresponding replacements.
2. Estimate size люфта landings of a steering shaft in axial plugs of a column. Check freedom of rotation of bearings of the kardanny hinge. In case of identification of signs of wear of plugs or the hinge the column is subject to replacement assembled.

Installation

Installation is made upside-down. Pay attention to the next moments:
   a) Track, that in the course of column installation forward wheels of the car were in rectilinear situation;
   b) All fixture should be tightened with demanded effort;
   c) The description of procedure of installation of a steering wheel is provided in the section Removal and installation of a steering wheel.