|
1. Transfer a control lever a suspension bracket to the situation "Maximum", then disconnect a negative wire from the battery.
2. Remove the central console (see. Removal and installation of the central console).
3. Remove a steering wheel (address to Head the Running gear and a steering).
4. Remove casings of a steering column (see. Removal and installation of elements of internal furnish of salon). |
|
5. At the corresponding complete set find under a steering column contact sockets of electroconducting of a radio tape recorder and a safety cushion and disunite them.
Contact sockets of electroconducting of a radio tape recorder (1) and safety cushions (2) under a steering column |
|
|
6. By means of a screw-driver release the clamp located in the right top corner of the rotating drum-type socket, located on the center of a steering column. |
|
|
7. Take the socket from a casing, having extended afterwards burn down electroconductings (in case of need remove right combined podrulevy the switch for free extraction of a plait). |
|
|
8. Turn out three fixing screws and remove a casing of the podrulevy switch from a steering column. |
|
|
9. Open a cover of the assembly block of safety locks for the purpose of ensuring access to the screw of fastening of the finishing panel located in a bottom corner of salon from the driver's party of the car. |
|
10. Turn out the top and bottom screws of fastening of the angular panel of furnish, then pull the panel forward and disconnect electroconducting of switches. Try to remember an order of connection of sockets, then remove the panel. |
|
|
11. Turn out three screws / release three clamps of fastening of the finishing panel of assembly of the switches located under an instrument guard. Liberate the left side of the panel from "Torpedo", then pull the panel forward and disconnect electroconducting from the switches built in in it (try to remember an order of connection of sockets). |
|
|
12. Remove the panel of switches. |
|
|
13. Having hooked a small screw-driver, accurately liberate from the top corners of the dashboard ("Torpedo") of the panel of high-frequency loudspeakers. Disconnect from loudspeakers electroconducting. |
|
|
14. Through openings under installation of loudspeakers liberate from clamps on the dashboard contact sockets and electroconducting plaits. |
|
15. Turn out two bottom and one top the screw of fastening of an instrument guard. Extend a guard on itself and disconnect from its lower part electroconducting. |
|
|
16. Remove a guard. |
|
|
17. Turn out fixing screws / release clamps and remove the section of furnish of a forward wall of a driver's foot well located under the dashboard.
18. Turn out two fixing screws on the left side of the panel of the bottom cover of a steering column. |
|
19. Turn out three remained screws of fastening of the panel of the bottom cover of a steering column/cover of the assembly block of safety locks. Access to screws is possible through a casing of the assembly block. Remove the panel. Where it is required, liberate from the panel electroconducting sockets. |
|
|
20. Disunite three contact sockets of electroconducting located under a steering column. |
|
|
21. Remove a steering column (address to Head the Running gear and a steering). |
|
22. Take from the dashboard an ashtray, then turn out two fixing screws in the lower part of facing of control panels heater/radio tape recorder functioning, by means of a small screw-driver accurately release fixing clamps and remove facing. |
|
|
23. On models from the dashboard located in the central part a radio tape recorder screw two fixing screws, then take radio tape recorder assembly from the panel and disconnect brought it a back part electroconducting and an antenna cable. |
|
24. Turn out four fixing screws and take from the dashboard a radio tape recorder casing. Where it is required, liberate from a casing sockets of electroconducting and an antenna cable. |
|
|
25. At the corresponding complete set turn out four fixing screws and take from the central dashboard the small ware shelf. |
|
26. Turn out two bottom fixing screws and take from the dashboard an ashtray/lighter casing, having disconnected electroconducting from the last and lamps of illumination of assembly. Remove a casing. |
|
|
27. Turn out four screws of fastening to control panel "Torpedo" heater functioning. |
|
28. Accurately hooking a small screw-driver, remove from the dashboard deflectors of two central ventilating snuffled. |
|
|
29. Turn out two fixing screws and take assembly of the central ventilating snuffled from the dashboard. |
|
|
30. Disconnect electroconducting from switches in the central part of the dashboard, hours and, at the corresponding complete set, - control the air temperature lamp/sensor in salon. |
|
|
31. Open a cover of a ware box, release a lock uvula in its back part, then completely lower a cover. Turn out six fixing screws. |
|
|
32. Take assembly of a ware box from the dashboard. |
|
|
33. Turn out fixing screws and remove a carpet upholstery under the panel of prior from the passenger party of the car. |
|
34. Hooking a small screw-driver, remove furnish panels from forward body racks. |
|
|
35. Remove assembly of the electromotor of a drive of cleaners of a windscreen (address to Head Onboard electric equipment). |
|
36. From an impellent compartment turn out three nuts of fastening of the dashboard to a partition. |
|
|
37. In salon of the car turn out the left screw of fastening of the lower part of the panel. |
|
|
38. Then give two right screws. |
|
|
39. From both parties of the top arm of a steering column turn out two screws of fastening of the dashboard to it. |
|
|
40. Also give two screws of fastening of the dashboard to the bottom arm of a column. |
|
|
41. Through a niche under installation of a radio tape recorder turn out the top bolt of fastening of the dashboard to heater assembly. |
|
|
42. In the lower part of the central section of the dashboard turn out the bottom screw of fastening of a bearing frame of the panel to a heater. Also turn out the screw of fastening of the panel to the right bearing frame which is not subject to removal from the car. |
|
|
43. Through an opening under radio tape recorder installation / the ware shelf (from its left side) turn out a bolt of fastening of a ventilating air line to the left bearing frame of the dashboard. |
|
|
44. Under the central part of the panel turn out a bolt of fastening of its left bearing frame to an arm on a car floor. |
|
|
45. Where it is required, take the back relay from the assembly block of safety locks for the purpose of a possibility of removal of the dashboard. |
|
|
46. By means of the assistant accurately delay dashboard assembly forward, separating it from a partition of an impellent compartment and liberating remained fixed electric sockets. Take the removed assembly through one of an apron of doors of the car, passing electroconducting through openings in it. Try to remember routes of laying of plaits. |
|