Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
- Body and salon furnish
   Care of components of a body and car bottom
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Removal and installation of a front bumper
   Removal and installation of a rear bumper
   Removal, installation and cowl adjustment
   Removal and installation of a driving cable of an otpuskaniye of the lock of a cowl
   Removal and installation of locks of a cowl
   Removal, installation and adjustment of doors
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of door handles and lock components
   Removal and installation of regulators of window regulators of door windows
   Removal, installation and adjustment of a door of a back and its telescopic emphasis
   Removal and installation of components of the lock of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive of door window regulators
   Removal and installation of door rear-view mirrors and accompanying components
   Windscreen, glass of a door of a back and the other fixed glasses - the general information
   The top hatch - the general information
   External body furnish
   Removal and installation of seats
   Removal and installation of seat belts
   Removal and installation of elements of internal furnish of salon
   Removal and installation of the central console
   Removal and dashboard installation
   Control body sizes
+ Onboard electric equipment
+ electric equipment Schemes



Removal and installation of components of the lock of a door of a back

Lock assembly

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Open a back door
3. Open hatches of access and disconnect electroconducting from assemblies of the back combined lamps built in at a door.

4. Remove clamps.
Bверху — Extraction of the central pin of a clamp
Below — Extraction of a clamp of fastening of the finishing panel of a door of a back



5. Turn out fixing screws.

6. Remove the bottom panel of furnish of a door of a back.

7. Mark the provision of heads of bolts of fastening of zamkovy assembly.

8. Turn out two fixing bolts and remove lock assembly, having disconnected from it an executive rod.

Installation

Installation is made upside-down. Pay attention to the next moments:
   a) Track correctness of installation of fixing bolts (according to the labels put in the course of dismantle);
   b) Before installation to the place of the finishing panel make sure of serviceability of functioning of the lock. In case of need weaken fixing bolts and as appropriate correct the provision of assembly. Having finished adjustment, strongly tighten fixing bolts and establish into place the furnish panel.

Lock cylinder

Removal

 PERFORMANCE ORDER

1. Execute the procedures described in subsection "Lock assembly - Removal", subitem 1 — 4.
2. At the corresponding complete set screw two fixing bolts and remove the block of the activator of the uniform lock. Having removed the servo-driver, disconnect from the lock an executive rod and electroconducting.

3. Turn out three fixing screws, take sideways the lock cylinder from a door and disconnect the remained executive rod.

4. For cylinder extraction from assembly remove a penoplastovy sealing ring, then insert a key into a keyhole and at the same time release a lock uvula of fastening of the cylinder. For a key take the cylinder.

Installation

Installation is made upside-down. Track for correctness of installation and reliability of fastening of an executive rod.

Lock drummer

Removal

 PERFORMANCE ORDER

1. Remove covers and turn out screws of fastening of the back panel of an upholstery of a luggage compartment. Remove the panel, having provided with that access to the lock drummer.

2. Unbend back edge of a carpet and turn out two bolts of fastening of the drummer. At the corresponding complete set liberate from drummer assembly the sensor switch of the anticreeping alarm system.

Installation

Installation is made upside-down.