Citroen Xantia

since 1993 of release

Repair and car operation

Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
- Body and salon furnish
   Care of components of a body and car bottom
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Removal and installation of a front bumper
   Removal and installation of a rear bumper
   Removal, installation and cowl adjustment
   Removal and installation of a driving cable of an otpuskaniye of the lock of a cowl
   Removal and installation of locks of a cowl
   Removal, installation and adjustment of doors
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of door handles and lock components
   Removal and installation of regulators of window regulators of door windows
   Removal, installation and adjustment of a door of a back and its telescopic emphasis
   Removal and installation of components of the lock of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive of door window regulators
   Removal and installation of door rear-view mirrors and accompanying components
   Windscreen, glass of a door of a back and the other fixed glasses - the general information
   The top hatch - the general information
   External body furnish
   Removal and installation of seats
   Removal and installation of seat belts
   Removal and installation of elements of internal furnish of salon
   Removal and installation of the central console
   Removal and dashboard installation
   Control body sizes
+ Onboard electric equipment
+ electric equipment Schemes

Removal, installation and adjustment of a door of a back and its telescopic emphasis

Back door



1. Disconnect a negative wire from the battery.
2. Open a back door.
3. Open hatches of access and disconnect electroconducting from the back combined lamps built in at a door.
4. Release clamps both turn out fixing screws and remove the bottom panel of an internal upholstery of a door of a back.
5. Release clamps of fastening of an emphasis of the back shelf on panels of a lateral upholstery of a door of a back (beat out the central pins, then take clamps). Remove an emphasis.

6. Turn out fixing screws and remove lateral panels from a back door.

7. Disconnect electroconducting from the consumers of the electric power located in a door (including contact sockets from both parties of a heater of back glass). If the door is not replaced, tie up to electroconducting plaits string pieces.
8. Accurately disconnect a hose of supply of liquid of washing of back glass from a nozzle on assembly of the electromotor of a screen wiper. Prepare for collecting spilled liquid. Liberate a hose from a door at the top together with an electroconducting plait.
9. Take from the top end face of a door rubber plugs of electroconducting through passage, then liberate from a door plaits of wires. Leave the tied-up pieces of a string sticking out of openings through passage.
10. Ask the assistant to take a door and serially release spring clamps of both telescopic emphasis. Liberate spherical hinges of an emphasis from reception nests on a door.

11. Screw fixing bolts and by means of the assistant remove a back door from the car. Transfer a door to a safe place.

Installation and adjustment


1. By means of the assistant get a door on the regular place, screw and tighten fixing bolts.

2. Further installation is made as it should be, the return to a dismantle order. Pay attention to the next moments:
   a) Filling at a door of plaits of electroconducting is made by means of left passed through openings of pieces of a string through passage;

   b) After installation of a door check uniformity of its arrangement of rather adjacent body panels. In case of need release adjusting bolts and make the corresponding adjustment. Having achieved satisfactory result, do not forget to tighten adjusting screws;

   c) Having adjusted the provision of a door, check serviceability of functioning of its locks. In case of need weaken fixing bolts (it is necessary to remove the back panel of furnish of a door - see. Removal and installation of components of the lock of a door of a back) and as appropriate correct position of locks.

Telescopic emphasis



1. Prop up a back door in open situation.

2. By means of a screw-driver with a flat sting release a spring clamp of a spherical support of a telescopic emphasis on a door.

3. Take a clamp from a support.

4. Repeat procedure, having released the hinge since the opposite end of an emphasis. Remove an emphasis from the car.


Installation is made upside-down. Track reliability of a zashchelkivaniye of clamps.