Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
- Engine repair
   - The repair procedures which are not demanding extraction of the engine from the car - petrol engines
      Check of kompressionny pressure in cylinders
      Fixing cranked / distributive shaft for the purpose of prevention casual in the course of performance of procedures of service of the car
      Removal and installation of a cover of a head of cylinders
      Removal and installation of a pulley of a cranked shaft
      Removal and installation of covers of a gas-distributing belt
      Belt of a drive of GRM - the general information, removal and installation
      Removal, check of a condition and installation of a natyazhitel and cogwheels of a gas-distributing belt
      Epiploon replacement (ов) camshaft
      Removal, check of a condition and installation of a camshaft and pushers of valves
      Check and adjustment of klapanny gaps
      Removal and installation of a head of cylinders
      Removal and installation of the pallet of a case of the engine
      Removal, check of a condition and installation of the oil pump
      Removal and installation of a maslookhladitel (model of 2.0 l)
      Replacement of epiploons of a cranked shaft
      Removal, check of a condition and flywheel installation / driving disk
      Check of a condition and replacement of support of a suspension bracket of the power unit
   + the Repair procedures which are not demanding extraction of the engine from the car - diesel engines
   + Removal and major maintenance of the engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


Removal, check of a condition and flywheel installation / driving disk

Removal

Flywheel (models with RKPP)

 PERFORMANCE ORDER

1. Remove a transmission (see. A manual box of gear shifting), afterwards remove coupling assembly (see. Head Coupling).

2. Block a gear wreath of a flywheel by means of the special adaptation, it is alternative приболтите a metal strip to a flywheel and the block of cylinders.

Do not try to fix at all a shaft by a prodevaniye of a blocking core in drilling in its pulley (see. Fixing cranked/distributive shaft for the purpose of prevention casual in the course of performance of procedures of service of the car)!

3. Turn out bolts of fastening of a flywheel and remove the last from a pin of a cranked shaft (the flywheel weighs quite a lot, - try not to drop it). If the directing pin is freely planted in the nest in an end face of a cranked shaft, take it and clean in a reliable place. At assembly bolts of fastening of a flywheel are subject to replacement without fail.

Driving disk (models with AT)

 PERFORMANCE ORDER

1. Remove transmission (see. Automatic transmission) Block a driving disk in the same way that is offered for flywheel fixing (see here subsection "A flywheel (models with RKPP)", item 2). Mark the provision of a driving disk in relation to the rotation converter, then weaken all fixing bolts.
2. Turn out bolts and remove them together with a plate of the converter of rotation and two adjusting washers (on one from each of the parties of a plate of the converter). Pay attention that washers differ on thickness, and thicker is established outside of a converter plate, and thinner - from within. Bolts of fastening of a driving disk are subject to replacement without fail.
3. Remove a driving disk from a pin of a cranked shaft. If the directing pin is freely planted in the nest in an end face of a cranked shaft, take it and clean in a reliable place.

Condition check

 PERFORMANCE ORDER

1. On models from RKPP attentively examine contacting to a coupling disk a working surface of a flywheel on existence of scratches and задиров. Make sure of lack of chips in the basis of teeths of a gear wreath. The working surface of a flywheel can be restored by a pro-point way, however replacement is more preferable. Do not hesitate to address for consultations to experts firm Citroёn company service centers. The gear wreath is not subject to shift and in case of its wear or damage also it is necessary to replace a flywheel.
2. On models from AT check a driving disk of the converter of rotation on existence of signs of deformation, inexact cracks round boltovy openings, or going radially from the disk center. Estimate degree of wear of a gear wreath and check teeths on existence of chips. In case of this sort of detection of defects the driving disk is subject to replacement.

Installation

Flywheel (models with RKPP)

 PERFORMANCE ORDER

1. Carefully smooth out interfaced surfaces of a flywheel and a pin of a cranked shaft. Remove traces of old hermetic from carving openings in an end face of a pin of a shaft (use a tap of the suitable size).

In the absence of near at hand suitable tap, saw through lengthways a fixing bolt and use it for carving pro-cleaning.

2. If the carving part of new bolts of fastening of a flywheel is not covered with fixing structure, grease it with hermetic suitable for this purpose.

3. Make sure available on the place of a pin of a shaft of a directing pin. Plant a flywheel on a pin and screw new fixing bolts.

4. Block a flywheel from a provorachivaniye (see here subsection "A flywheel (models with RKPP)", item 2) and tighten bolts of its fastening with demanded effort.

5. Establish into place coupling assembly (see. Head Coupling). Remove the adaptation blocking a flywheel and establish into place a transmission (see. Manual box of gear shifting).

Driving disk (models with AT)

 PERFORMANCE ORDER

1. Execute the procedures stated here in subsection "A flywheel (models with RKPP)" in subitem 1 — 2 (with the amendment that deal not with a flywheel, and with a driving disk).
2. Plant a disk on directing pin on a shaft pin.
3. Press a plate of the converter of rotation (thick washers outside). Achieve combination of the landing labels put in the course of dismantle.
4. Screw fixing bolts, block a shaft from a provorachivaniye (see above "Condition check", item 1) and tighten fixture with demanded effort.
5. Remove the adaptation blocking a disk and establish into place transmission (see. Automatic transmission).