Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
- Transmission
   - Manual box of gear shifting
      Replacement of transmission oil
      Drive of the mechanism of gear shifting - the general information and adjustment
      Removal and installation of components of a drive of gear shifting
      Replacement of epiploons
      Check of serviceability of functioning, removal and installation of the sensor switch of fires of a backing
      Removal and installation of a drive of a speedometer
      Removal and transmission installation
      Major maintenance of RKPP - the general information
   + Automatic transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


Replacement of epiploons

Epiploons of power shafts

 PERFORMANCE ORDER

1. Cock the parking brake and prop up protivootkatny boots back wheels. To Poddomkratta a car front also establish it on props. Remove the corresponding forward wheel.
2. Merge transmission oil (see. Replacement of transmission oil).
3. Give a nut of the bottom spherical support, take out a coupling bolt and liberate a shaft of a spherical finger from stupichny assembly (address to Head the Running gear and a steering).

Right power shaft

 PERFORMANCE ORDER

1. Weaken nuts of two bolts of fastening of the intermediate bearing, then develop bolts under 90 ° so that their asymmetric heads released an external holder of the bearing.
2. Accurately delay stupichny assembly outside and, liberate the intermediate bearing from the basic arm.
3. After the internal end of a shaft will be liberated from transmission, remove from it a dustproof cover (try to remember the adjusting provision of a cover on shaft assembly). Prop up the internal end of a shaft such in order to avoid damage of the external CV JOINT.

4. Having accurately hooked a screw-driver with a flat sting, take an epiploon of a power shaft from the landing nest in RKPP case.

5. Carefully wipe a surface of a case of a transmission round a nest under epiploon landing, grease with dense greasing external sponges of a new epiploon. Fill an epiploon in a nest and by means of a suitable opravka plant it perpendicularly on the regular place against the stop in a nest coat hanger (as an opravka the face head of the corresponding size or a piece of a pipe of the corresponding diameter will approach - the opravka should rest only against the firm external region of an epiploon).

6. If the epiploon is equipped with a plastic protector, do not remove it until the power shaft will be established into place.

7. Carefully wipe shlitsa on a pin of a power shaft, and grease them with a thin layer of greasing. With the same greasing grease epiploon sponges in a nest of a case of RKPP.
8. Plant on the place on a shaft a rubber dustproof casing (the flat party to transmission).
9. Accurately fill shlitsa of a shaft in a lateral gear wheel of differential (try not to damage an epiploon), then level the intermediate bearing concerning the basic arm and get a shaft in regular situation. In case of need use a hammer with soft brisk for landing of an external holder of the bearing in an arm.
10. Make sure of correctness of landing of the intermediate bearing and fix it, having developed under 90 ° fixing bolts with asymmetric heads. Tighten with demanded effort fixing nuts. At the corresponding complete set remove a plastic protector and press a dustproof cover to a transmission case, having densely covered an epiploon.
11. Fill in stupichny assembly a shaft of a finger of the bottom spherical support. Track correctness of landing in a nave of a protective cover of the hinge. Establish a coupling bolt, screw a nut and tighten it with demanded effort (address to Head the Running gear and a steering).
12. Establish into place a wheel, lower the car on the earth and tighten bolts of fastening of a wheel with demanded effort.
13. Fill in in a transmission necessary amount of transmission oil of a demanded grade (address to Head Routine maintenance).

Left power shaft

 PERFORMANCE ORDER

1. Delay stupichny assembly outside and take the internal CV JOINT of a power shaft from transmission. Prop up a shaft in order to avoid damage of the external CV JOINT or protective covers of hinges.
2. Replace an epiploon, operating in an order stipulated in subsection "Right power shaft", subitem 4 — 6.
3. Accurately fill shlitsa of the internal CV JOINT in a lateral gear wheel of differential. Try not to damage a new epiploon. Where it is required, remove from an epiploon a plastic protector.
4. Execute the procedures described in subsection "Right power shaft", subitem 11 — 13.

Epiploon of primary shaft

 PERFORMANCE ORDER

1. Remove a transmission (see. Removal and transmission installation).
2. Turn out three fixing bolts and remove directing coupling from a pin of primary shaft of RKPP (the coupling acts in film together with sealing ring/laying). Remove adjusting or persistent washers, usually podlipayushchy couplings to the back party and put on them back a shaft pin.

3. Having accurately hooked a screw-driver, take an old epiploon from assembly of the directing coupling.

4. Before installation check a surface of a pin of primary shaft contacting to it and a nest wall in the directing coupling on existence of roughnesses and задиров, capable to bring to an exit of a new epiploon out of operation. Insignificant defects can be removed with a way of polishing by a fine-grained emery paper. In more serious cases it is required to replace primary shaft. Wipe a pin of a shaft and grease it for the purpose of simplification of landing of an epiploon.
5. Dunk a new epiploon into pure impellent oil and plant it in the nest in the directing coupling.

6. Accurately put on the coupling with the epiploon established in it a pin of primary shaft, screw fixing bolts and tighten them with demanded effort.





7. Taking an opportunity, check a condition of components of coupling (see. Head Coupling), then establish transmission on a place (see. Removal and transmission installation).

Epiploon of a rod of a choice of transfers

 PERFORMANCE ORDER

1. Park the car on an equal horizontal platform, whenever possible with a firm covering. Prop up protivootkatny boots back wheels, then поддомкратьте a front of the car and establish it on props. Remove the left forward wheel and dismantle an access cover from a loker.
2. Having hooked a screw-driver, liberate a sharovy tip of driving draft from the hinge of a rod of a choice of transfers to transmissions. Disconnect draft.

3. Accurately take a rod epiploon from the nest in RKPP case.

4. Remove it from a shaft pin.

5. Before installation of a new epiploon check a condition of surfaces of a rod contacting to it and nest walls in a case. Remove insignificant defects by means of a fine-grained emery paper. In case of identification deep задиров it is necessary to make rod replacement.
6. Slightly grease external edge and sponges of a new epiploon with dense greasing, then accurately put on an epiploon a pin of a rod and by means of a suitable opravka plant it in a nest in a transmission case.
7. Connect to a rod driving draft, having tracked reliability of joining of the spherical hinge. Lower the car on the earth.