Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
- Systems of cooling, heating
   Detachment and replacement of hoses of system of cooling
   Removal, check of a condition and radiator installation
   Removal, check of serviceability of functioning and thermostat installation
   Check of serviceability of functioning, removal and fan installation (ов) cooling systems
   Check of serviceability of functioning, removal and installation of electric switches and sensors of system of cooling
   Removal and installation of the water pump
   Removal and installation of a casing of the thermostat / fuel filter (diesel models)
   System of heating/ventilation of salon - the general information
   Removal and installation of components of system of heating/ventilation of salon
   Air central air - the general information and precautionary measures
   Removal and installation of components of central air of air
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


Removal and installation of components of system of heating/ventilation of salon

Assembly of management by heater functioning

Procedures of dismantle and installation of assembly of management by functioning of a heater are among demanding from the performer of rather high qualification, and it will be more correct to charge their performance to specialists of car repair shop.

Removal

 PERFORMANCE ORDER

1. Remove dashboard assembly (address to Head the Body and salon furnish).
2. Having released clamps, uncover the top part of the control panel.
3. Release srezny clamps of fastening of cables of management and disconnect tips of cables from control unit levers.

4. Disconnect electroconducting from the control unit and lamps of illumination of the panel.



Installation

Installation is made upside-down. Before a zashchelkivaniye to the place of the dashboard make sure of serviceability of functioning of levers of the control panel. Installation of the dashboard make according to the instructions provided in Head the Body and furnish of salon.

Cables of management of heater functioning

Removal

 PERFORMANCE ORDER

1. Turn out two bottom fixing screws, then having accurately hooked a small screw-driver, release clamps and remove control panel facing by radio receiver/heater functioning.
2. On the models equipped with the ware shelf in the central part of the dashboard, turn out four fixing screws and remove the ware shelf.
3. On the models equipped with an autoradio tape recorder, turn out two fixing screws, take a radio tape recorder from the dashboard and disconnect from its back part electroconducting and an antenna cable.
4. Turn out four screws and remove a radio tape recorder casing. At the corresponding complete set disconnect from a casing electroconducting and an antenna cable.
5. For the purpose of ensuring access to the top driving cables of assembly of management, release clamps and uncover management assemblies.
6. Access to the bottom cables opens after an otpuskaniye of screw fixture and control panel extraction from the dashboard.
7. For removal of cables release srezny clamps and disconnect tips of cables of control levers.
8. To disconnect a cable tip from the heater block, be appropriated for the dashboard (in case of need remove the bottom sections of the panel) and disconnect cables, operating as it is described above.
9. Try to remember routes of laying of removed cables.

Installation

Installation is made upside-down. Pay attention to the next moments:
   a) Track correctness of laying of cables of management;
   b) Track reliability of fixing of cables srezny clamps;
   c) Before establishing the components removed for the purpose of ensuring access, make sure of serviceability of functioning of assembly of management of a heater.

Heater heat exchanger

Procedures of dismantle and installation of the heat exchanger are among demanding from the performer of rather high qualification, and it will be more correct to charge their performance to specialists of car repair shop. New sealing rings of the shlangovy socket will be necessary.

Removal

 PERFORMANCE ORDER

1. Remove dashboard assembly (address to Head the Body and salon furnish).

2. Turn out four screws of fastening of a directing casing of electroconducting to a casing of a heater and an arm of a steering column.



3. Give two top nuts of fastening of the right assembly bracket of the dashboard to an arm of a steering column.

4. Turn out the bottom bolt of fastening of the right assembly bracket of the dashboard to a floor, then liberate from an assembly bracket electroconducting.

5. Remove a bracket.

6. Disconnect electroconducting from the electromotor of the fan of a heater, its resistor and the control panel a heater. Liberate a plait from intermediate clamps on heater assembly.

7. Release clamps and uncover the top part of the control panel heater functioning. Disconnect electroconducting from illumination lamps.
8. Empty cooling system (address to Head Routine maintenance).
9. In an impellent compartment, necessarily, uncover a camshaft (see. Head engine Repair) for the purpose of ensuring access to the shlangovy socket of the heat exchanger of a heater on a back partition.
10. Where it is required, release a metal clip in the top part of the socket.
11. Release a clamp, having wrung out it to the left (see. Detachment and replacement of hoses of system of cooling).

12. Turn out two screws of fastening of a facing level of the shlangovy socket to a partition of an impellent compartment.

13. Remove a facing level together with a sealant.

14. In an impellent compartment give a bolt and two nuts of fastening of assembly of a heater to a partition (do not forget about washers).



15. In salon remove assembly of a heater and disconnect from it an air line. Prepare for collecting spilled cooling liquid.

Not to soil a carpet, cover a salon floor with a polyethylene film.

16. Having dismantled heater assembly, remove a level of fastening of branch pipes with a penoplastovy sealant, then release four clamps and take from heater assembly the heat exchanger.





Installation

Installation is made upside-down. Pay attention to the next moments:
   a) Do not forget to establish into place a plate of fastening of branch pipes with a penoplastovy sealant;
   b) Do not forget to pass a heater tube through the plug through passage in a partition of an impellent compartment;
   c) Installation of the dashboard make according to the instructions provided in Head the Body and furnish of salon;
   d) In summary do not forget to make filling of system of cooling (address to Head Routine maintenance).

Electromotor of the fan of a heater

Removal

 PERFORMANCE ORDER

1. Release fixing clamps / turn out screws and remove the carpet panel of furnish under the dashboard from the passenger party of the car.

2. Give three fixing screws, then omit assembly of the electromotor and disconnect from it electroconducting.



3. Now the motor can be separated from a krylchatka by a way of a reversing of two fixing screws.

Installation

Installation is made upside-down.

Resistor of the electromotor of a drive of the fan of a heater

Removal

 PERFORMANCE ORDER

1. Release fixing clamps / turn out screws and remove the carpet panel of furnish under the dashboard from the passenger party of the car.
2. The resistor is established in the basis of a casing of a heater, near the driving electromotor of the fan.

3. Turn the basis of resistive assembly, separate it from a casing of a heater and disconnect electroconducting.

Installation

Installation is made upside-down.