Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
- Power supply system and release
   - Power supply system - petrol models
      Removal and installation of assembly of an air purifier
      Removal, installation and adjustment of a cable of gas
      Removal and installation of a pedal of gas
      Unleaded fuel - the general information and use rules
      Systems of injection of fuel - the general information
      Sbrasyvaniye of pressure in a power supply system
      Removal and installation of the fuel pump
      Removal and installation of the sensor of fuel consumption
      Removal and installation of a fuel tank
      Check of a condition and adjustment of system of injection of fuel
      Removal and installation of the case of a throttle
      Removal and installation of components of Bosch Motronic 5.1 system
      Removal and installation of components of Magneti-Marelli 8Р system
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
   + the Power supply system - diesel models
   + Systems of decrease in toxicity and production of the fulfilled gases
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes



Removal, installation and adjustment of a cable of gas

Removal


Knot of fastening of a cable of gas to the throttle case (to model with RKPP)


Knot of fastening of a cable of gas to the throttle case (to model with AT)

 PERFORMANCE ORDER

1. In an impellent compartment disconnect the core of a cable of gas from the throttle case, extend a cable from the rubber plug of an arm through passage and remove a spring clamp (see illustrations Knot of fastening of a cable of gas to the throttle case (to model from RKPP) and Knot of fastening of a cable of gas to the throttle case (to model from AT)).
2. Moving back lengthways on a cable, liberate it from intermediate directing clamps and bindings. Try to remember a route of laying of a cable.
3. Release clamps and remove section of the bottom felt furnish under the dashboard from the driver's party of the car.
4. In salon of the car release a clamp of a cover of the assembly block of safety locks, having turned it on a turn quarter counter-clockwise. Uncover the assembly block the dashboard.
5. Release a clip and disconnect the cable core from the top part of a pedal of gas.
6. Liberate a cable cover from the holder on a pedal arm. Tie up by the cable end a string piece.
7. Return to an impellent compartment and liberate the rubber plug of a cable through passage from a back partition. Then, having pulled a cable on itself, involve it in an impellent compartment. Untie from a tip a string and leave it passed through a partition.
8. Attentively examine a cable, checking it on existence of signs of wear or mechanical damages. Also check a condition of the rubber plug through passage. Defective components replace.

Installation

 PERFORMANCE ORDER

1. Tie up a cable to a string and involve it through a partition in car salon. Untie from a tip a string and latch a cable cover in the holder of an arm. The core connect by the pedal end.
2. Check reliability of fastening of a cable and landing in a partition of the rubber plug through passage. Establish into place the felt panel of furnish of the dashboard and a cover of the assembly block of safety locks.
3. Having returned to an impellent compartment, make sure of correctness of landing of a cover of a cable in the plug through passage, then, moving along a cable and watching correctness of a route of laying, fix it in all intermediate clamps and bindings.
4. Put on a flat washer a tip of a cable and establish a spring clamp.
5. Pass a cable cover in the plug of an arm through passage on the throttle case. The core of a cable connect to a cam of a drive of a butterfly valve. Make cable adjustment (see below).

Adjustment

 PERFORMANCE ORDER

1. In an impellent compartment remove a spring clamp from a cover of a cable of gas. Make sure that the cam of a drive of a zaslonka is pressed to an emphasis. Smoothly pull a cable from the plug through passage, having completely chosen a core weak point.
2. Having fixed a cable in this situation, establish a spring clamp in the last from open flutes in front of the rubber plug through passage. After installation of a clip and a cover otpuskaniye, the weak point of the core of a cable should appear very insignificant.
3. Ask the assistant to squeeze out a pedal of gas and make sure that the cam of a drive passes to the extreme situation corresponding to complete opening of a zaslonka. At a pedal otpuskaniye the cam should come back smoothly to a starting position, nestling on an emphasis.
4. On models from AT, having finished with a gas cable, check adjustment of a driving cable of inclusion of the kick-down mode (see. Automatic transmission).