Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
- Power supply system and release
   - Power supply system - petrol models
      Removal and installation of assembly of an air purifier
      Removal, installation and adjustment of a cable of gas
      Removal and installation of a pedal of gas
      Unleaded fuel - the general information and use rules
      Systems of injection of fuel - the general information
      Sbrasyvaniye of pressure in a power supply system
      Removal and installation of the fuel pump
      Removal and installation of the sensor of fuel consumption
      Removal and installation of a fuel tank
      Check of a condition and adjustment of system of injection of fuel
      Removal and installation of the case of a throttle
      Removal and installation of components of Bosch Motronic 5.1 system
      Removal and installation of components of Magneti-Marelli 8Р system
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
   + the Power supply system - diesel models
   + Systems of decrease in toxicity and production of the fulfilled gases
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


Removal and installation of components of Magneti-Marelli 8Р system

L models 1.6 and 1.8

Injection injectors

Before the beginning of performance of procedure attentively familiarize with section Power supply system preventions - petrol models!


Before making the decision on replacement of a faulty injector, test on it any of widespread now special cleaners.


 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Remove a sleeve connecting an air purifier to the case of a throttle (see. Removal and installation of assembly of an air purifier).
3. Turn out two bolts of fastening of directing electroconducting to the top part of the pipeline. Take directing aside, having provided unhindered access to injectors of injection of fuel.
4. Release a fixing clamp (ы) and disconnect electroconducting from the corresponding injector (ов).
5. Turn out fixing screws and remove a plate (ы) fastenings of injectors (injectors of No. No. 1 and 2 fasten one plate, No. No. 3 and 4 - another).
6. Wrap up an injector subject to removal by rags for the purpose of prevention of disorder of fuel, then carefully weaken injector landing in the fuel highway. Take an injector and remove from it a sealing ring. Sealing rings of removed injectors at assembly are subject to replacement without fail!
7. Before installation plant on an injector a new sealing ring. Slightly grease a ring with pure impellent oil and plant an injector in the corresponding nest in the fuel highway.
8. Make sure of correctness of landing of all injectors, then establish into place a fixing plate (ы). Strongly tighten screws of fastening of a plate, then connect to an injector (ам) electroconducting.
9. Return into place directing electroconductings and strongly draw it bolts to the pipeline.
10. Establish the air sleeve connecting an air purifier to the case of a throttle, then connect a negative wire to the battery, start the engine and check injectors on existence of signs of leaks.

Regulator of pressure of fuel

See. Removal and installation of components of Bosch Motronic 5.1 system.

Potentiometer of an axis of a butterfly valve

The potentiometer is established on the right on the throttle case. At first disconnect a negative wire from the battery.

 PERFORMANCE ORDER

1. Release a fixing clamp and disunite the contact socket of electroconducting of a potentiometer.

2. Turn out two fixing screws and remove a potentiometer from the throttle case.
3. Installation is made upside-down. Track for correctness of introduction of a potentiometer in gearing with a butterfly valve axis.

Electronic control unit (ECU)

See. Removal and installation of components of Bosch Motronic 5.1 system.

Step-by-step motor of adjustment of turns of idling

The step-by-step motor is located from the forward party of the case of a throttle. At first disconnect a negative wire from the battery.

 PERFORMANCE ORDER

1. Release a fixing clamp and disunite the contact socket of electroconducting of the motor.

2. Turn out two fixing screws and remove the motor from the throttle case.
3. Installation is made upside-down.

The sensor of absolute pressure in the pipeline (MAR)

See. Removal and installation of components of Bosch Motronic 5.1 system.

The sensor of temperature of cooling liquid

See. Head of System of cooling, heating.

The sensor of temperature of soaked-up air (IAT)

The IAT sensor is located on the throttle case.

 PERFORMANCE ORDER

1. Remove a potentiometer of an axis of a butterfly valve (see above subsection "Potentiometer of an axis of a butterfly valve").
2. Release a fixing clamp and disunite the contact socket of electroconducting of the sensor.
3. Turn out the screw of fastening of the socket of the sensor to the top part of the case of a throttle, then accurately take the sensor from the throttle case. Check a condition of a sealing ring, in case of need make replacement.
4. Installation is made upside-down. Do not forget to replace the failed sealing ring. Track correctness of introduction of a potentiometer in gearing with a butterfly valve axis.

Sensor of provision of a cranked shaft

See. Removal and installation of components of Bosch Motronic 5.1 system.

Block of the relay of system of injection of fuel

See. Removal and installation of components of Bosch Motronic 5.1 system.

Heating element of the throttle chamber

The heating element is established in the top part of the case of a throttle. At first disconnect a negative wire from the battery.

 PERFORMANCE ORDER

1. Release a fixing clamp and disunite the contact socket of electroconducting of a heating element.

2. Turn out the screw (ы) fastenings of the contact socket of a heating element to the throttle case, then separate the socket and carefully take an element from the throttle case. Check a condition of a sealing ring, in case of need make replacement.
3. Installation is made upside-down. Do not forget to replace the failed sealing ring. Track, that electroconducting of a heating element did not appear is clamped at a screw tightening (ов) socket fastenings.

Models of 2.0 l

Fuel highway and injectors of injection of fuel

Before the beginning of performance of procedure attentively familiarize with section Power supply system preventions - petrol models!


Before making the decision on replacement of a faulty injector, test on it any of widespread now special cleaners.


 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Remove the air sleeve connecting an air purifier to the case of a throttle (see. Removal and installation of assembly of an air purifier).
3. Disconnect a vacuum tube from a regulator of pressure of fuel.
4. Release a fixing clamp and disconnect various hoses from the top part of the fuel highway.
5. Without forgetting about the preventions made in the section of Sbrasyvaniye of pressure in a power supply system, weaken fixing collars and disconnect hoses of giving and fuel return from the fuel highway. At assembly it is necessary to replace factory collars of braided type more practical screw or worm.
6. Release lock clamps and disunite contact sockets of electroconducting of four injectors of injection.
7. Give three fixing bolts and accurately remove assembly of the fuel highway with injectors from the inlet pipeline. Take the removed assembly from the car. Remove sealing rings from end faces of all injectors (at assembly they are subject to replacement without fail).
8. Remove a lock ring (ы) and take the corresponding injector (ы) from the fuel highway. Remove the top sealing ring (ы) from each of the removed injectors. All sealing rings at assembly are subject to replacement!
9. Installation is made upside-down. Pay attention to the next moments:
   a) Do not forget to establish on all acting in film injectors new sealing rings;
   b) For simplification of landing of injectors it is necessary to grease their sealing rings with pure impellent oil slightly;
   c) In summary the engine should be started and checked on existence of signs of leakages of fuel.

Regulator of pressure of fuel

See. Removal and installation of components of Bosch Motronic 5.1 system.

Potentiometer of an axis of a butterfly valve

 PERFORMANCE ORDER

1. Remove the throttle case (see. Removal and installation of the case of a throttle).
2. Disconnect electroconducting, then give two fixing screws and remove a potentiometer from the throttle case.
3. At installation track correctness of introduction of a potentiometer in gearing with a zaslonka axis. Strongly tighten fixing screws.
4. Establish into place the throttle case (see. Removal and installation of the case of a throttle).

Electronic control unit (ECU)

ECU is placed in the plastic box fixed on a mudguard of the right forward wheel. For removal of ECU it is necessary to disconnect a negative wire from the battery.

 PERFORMANCE ORDER

1. Remove from a box a cover, then disunite the socket of electroconducting of ECU.

2. Take ECU from the box. In case of need give fixing nuts and separate the block from an assembly plate.

3. Installation is made upside-down. Track reliability of fixing of the electric socket.

Step-by-step motor of adjustment of turns of idling

See information provided above in subsection "l Models 1.6 and 1.8 - the Step-by-step motor of adjustment of turns of idling".

The sensor of absolute pressure in the inlet pipeline (MAR)

The MAR sensor is in an arch of the right forward wheel.

 PERFORMANCE ORDER

1. At first disconnect a negative wire from the battery.
2. Give three fixing nuts and liberate the sensor from below from a basic arm.
3. Release a clamp and disconnect from the sensor electroconducting and a vacuum hose. Remove the sensor from the car.
4. Installation is made upside-down.

The sensor of temperature of cooling liquid

See. Head of System of cooling, heating.

The sensor of temperature of soaked-up air (IAT)

The IAT sensor is located in the basis of the case of a throttle.

 PERFORMANCE ORDER

1. Remove the throttle case (see. Removal and installation of the case of a throttle), then turn out two fixing screws and remove from the throttle case a potentiometer of an axis of a butterfly valve.
2. Walk on electroconducting back from the sensor to the contact socket of electroconducting. Turn out the screw of fastening of the socket to the throttle case.
3. Accurately remove the sensor from the regular place and take it from the throttle case. Check a condition of a sealing ring, in case of need make replacement.
4. Installation is made upside-down. Do not forget to replace the failed sealing ring. Track correctness of introduction of a potentiometer in gearing with a butterfly valve axis.

Sensor of provision of a cranked shaft

See. Removal and installation of components of Bosch Motronic 5.1 system.

Block of the relay of system of injection of fuel

See. Removal and installation of components of Bosch Motronic 5.1 system.

Heating element of the throttle chamber

See information provided in the corresponding subsection of models 1.6 and 1.8 of l.

Sensor of speed of movement of the car (VSS)

VSS is built in assembly of a drive of a speedometer (see. Manual box of gear shifting).

Detonation sensor

The sensor of a detonation will screw in a back wall of the block of cylinders.

 PERFORMANCE ORDER

1. For the purpose of ensuring access to the sensor prop up protivootkatny boots back wheels, then поддомкратьте a front of the car and establish it on props. Access to the sensor from under the car now will open.
2. Walk on electroconducting back from the sensor to the contact socket of electroconducting. Disconnect sensor electroconducting from the main plait.
3. Turn out a bolt of fastening of the sensor to the block of cylinders and take the sensor from under the car.
4. Installation is made upside-down. Track correctness of laying of electroconducting and reliability of a tightening of a fixing bolt.