Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
- Routine maintenance
   + Weekly checks
   - Routine maintenance of the car - petrol models
      Regular service
      Replacement of impellent oil and oil filter
      Check of a condition of hoses, and identification of sources of leaks
      Check of adjustment of coupling
      Check of level of ATF
      Suspension bracket and steering drive
      Check of a condition of protective covers of power shafts
      Reading of memory of the block of self-diagnostics
      Replacement of the dust removal filter (model with To/in)
      Check of a condition of a coolant of central air of air
      Replacement of spark plugs
      Check of a condition of system of ignition
      Check and adjustment of turns and quality of a mix of idling
      Check of serviceability of functioning of systems of decrease in toxicity of the fulfilled gases
      Check of a condition and replacement of a belt of a drive of auxiliary units
      Greasing of the mechanism of a drive of switching off of coupling
      Check of a condition of blocks of brake mechanisms of lobbies and back wheels
      Check of serviceability of functioning and adjustment of the parking brake
      Trial runs
      AT transmission liquid replacement
      Greasing of locks and loops
      Replacement of a filtering element of an air purifier
      Check of level of transmission oil (model with RKPP)
      Replacement of the fuel filter
      Replacement of hydraulic LHM liquid and returnable filter
      Check of a condition of brake supports, disks and hydraulic hoses
      Replacement of a belt of a drive of GRM
      Replacement of cooling liquid
   + Routine maintenance of the car - diesel models
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes



Check of a condition of hoses, and identification of sources of leaks

THROUGH EACH 15 000 KM (9000 MILES) RUN OR TIMES IN 12 MONTHS

 PERFORMANCE ORDER

1. Examine outside interfaced surfaces of the power unit, paying attention to traces of leakages of oil and cooling liquid. It is necessary to give special attention to joints of prokladochny surfaces of a cover of a camshaft, a head of cylinders, the oil filter and the case pallet. There are no bases to worry concerning existence of lungs потеков which emergence is quite natural eventually. Should guard only traces of really serious leaks at which identification it is necessary to make replacement corresponding a laying/epiploon (see below in the corresponding Chapter).
2. In parallel check a condition and reliability of fastening on the unions of all hoses and the metal tubes concerning functioning of the engine. Track reliability of fastening of lines hummock bandages, collars and intermediate clamps. In order to avoid wiping of lines replace the broken clamps new.
3. Attentively examine radiatorny hoses and hoses of system of heating of salon on all their length. At identification of cracks, swellings or traces of aging of a material make replacement of a defective hose.

Cracks come to light at a hose peregibaniye easier. Carefully check a condition of collars of fastening of hoses on connecting branch pipes of components of system of cooling. Do not forget that often hoses fray and wear out in installation sites of collars. It will be most correct to replace the failed collars of braided type more practical screw or worm.

4. Attentively examine on existence of traces of leaks all components of system of cooling (the hoses, interfaced surfaces, etc.).

Remember that leakages of cooling liquid usually represent a poroshkoobrazny raid of white or reddish color.

5. In case of need replace a defective component or the damaged laying (see. Head of System of cooling, heating).
6. At the corresponding complete set check also a condition of hoses of a path of cooling of ATF.
7. Having raised the car over the earth, check a condition of a jellied mouth of a fuel tank. The site of a joint of a mouth with the tank case is especially critical. Pay attention to existence of cracks, punctures, traces of aging of rubber and other defects. Sometimes leaks start to develop as a result of weakening of fixing collars.
8. Attentively check a condition of all rubber and metal fuel lines connecting a fuel tank to the engine. Pay attention to dents, flattening, a perekruchivaniye and other other defects. Make sure that ventilating hoses and tubes are not overwound round a jellied mouth of a tank. Make necessary corrections, replace defective sections. Do not forget to check a condition passing under the bottom of the car of lines of a hydraulic path.
9. In an impellent compartment check reliability of shtutserny connections of fuel, vacuum and brake lines. Estimate a condition of all hoses.