Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
- Brake system
   Pumping of hydraulic system
   Replacement of hoses and tubes of a hydraulic path of brake system
   Replacement of blocks of disk brake mechanisms of forward wheels
   Replacement of blocks of disk brake mechanisms of back wheels
   Condition check, removal and installation of brake disks
   Removal, major maintenance and installation of supports of disk brake mechanisms of forward wheels
   Removal, major maintenance and installation of supports of disk brake mechanisms of back wheels
   Removal, major maintenance and installation of the valve of management
   Removal and installation of a pedal of a foot brake
   The parking brake - general information and adjustments
   Removal and installation of a control lever of the parking brake
   Removal and installation of cables of a drive of the parking brake
   Removal and installation of the sensor switch of stoplights
   System of anti-blocking of brakes (ABS) - the general information
   Removal and installation of components of system of anti-blocking of brakes
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


Removal and installation of cables of a drive of the parking brake


Scheme of a hummock drive of the parking brake

1 — Fastening to the brake mechanism
2 — the Equalizer
3 — the Lock-nut (20 Nanometers)
4 — the Adjusting nut

And — the Scheme of connection of a cable to the brake mechanism
In — the Scheme of connection of primary cable to the equalizer

The drive of the parking brake is carried out by means of three metal cables. Primary driving cable connects a control lever to equalizer assembly from which two separate cables go to executive levers of supports of brake mechanisms of forward wheels of the car (see an illustration the Scheme of a hummock drive of the parking brake).

Primary cable

At assembly new rivets for thermofilter fastening be required.


Details of fixture of the main thermofilter of the bottom of the car

And — Draught of a drive of gear shifting
In — the Bolt and a nut of fastening of draft of a drive of gear shifting
With — the Main thermofilter

D — Clamps of fastening of the main thermofilter
Е — the Small thermofilter


Detachment of secondary cables of a drive of the parking brake from equalizer assembly

And — Otzhimaniye of a cable tip in a cover
In — Liberation of the right cable (wring out a tip up)

With — Liberation of the left cable (wring out a tip down)


Components of the equalizer of a hummock drive of the parking brake

A — Nuts directing primary cable
In — Directing primary cable
With — Assembly of primary cable

D — Nuts of fastening of the equalizer
Е — equalizer Assembly

Removal

 PERFORMANCE ORDER

1. To Poddomkratta the car also establish it on props. Remove forward wheels.
2. Weaken a lock-nut of fastening of a driving cable on a support of the brake mechanism. Afterwards give an adjusting/fixing nut and disconnect a cable from a support. Liberate a cable tip from the executive lever of the brake mechanism.
3. Under the car dismember spherical hinges of fastening of drafts of a drive of gear shifting to the switching mechanism.
4. Remove a reception pipe of system of production of the fulfilled gases (see. Systems of decrease in toxicity and production of the fulfilled gases).
5. Drill rivets and remove the small thermofilter of system of production of the fulfilled gases from the car bottom.
6. Give a nut, take a fixing bolt and disconnect draft of a drive of gear shifting from the basis of the lever of switching (see an illustration of the Detail of fixture of the main thermofilter of the bottom of the car).
7. Remove the second small thermofilter.
8. Release clamps and remove from the car bottom the main thermofilter for the purpose of ensuring access to the equalizer of a hummock drive of the parking brake.
9. Grasp a tip of one of secondary driving cables and push the cable core in its cover, at the same time liberating a cable from equalizer assembly (see an illustration the Detachment of secondary cables of a drive of the parking brake from equalizer assembly). Repeat procedure for the second cable.

For liberation from the equalizer of the right secondary cable of a drive of the parking brake its tip should be wrung out up. The tip of the left cable is liberated by an otzhimaniye down.

10. It is enough to disconnect cables from the equalizer, - need for their liberation from directing is absent.
11. In salon of the car remove the central console (address to Head the Body and salon furnish).
12. Completely release a control lever of the parking brake and disconnect from it primary driving cable.
13. Under the car give two nuts of fastening directing primary cable to a floor, then release two nuts of fastening of assembly of the equalizer (see an illustration Components of the equalizer of a hummock drive of the parking brake).
14. Remove assembly of primary cable of a drive of the parking brake and take it from under the car.

Installation

 PERFORMANCE ORDER

1. Get assembly of primary cable on the regular place, then screw and tighten nuts of fastening of the equalizer.
2. Check a condition of the sealing laying established under directing primary cable, in case of need make replacement. Establish directing and tighten nuts of its fastening.
3. Slightly grease with dense greasing a site of a cable adjacent to a tip from the equalizer.
4. In salon of the car connect the second tip of a cable to a control lever of the parking brake, then establish into place the central console (address to Head the Body and salon furnish).
5. Now connect to the equalizer secondary cables. Pay attention that the right cable is equipped with a white emphasis of a cover and is got in the top opening in assembly whereas the emphasis of a cover of the equalizer of the left cable got in the bottom opening is painted in black color. At connection of cables act in the following order:
   a) Press an emphasis of a cover of a cable to the equalizer;
   b) Having grasped a cable tip from a support, push the core in a cover and get its opposite end in the corresponding reception opening in the equalizer;
   c) Now extend a cable from a cover towards a support and make sure of correctness of its gearing in the equalizer.
6. Slightly grease with dense greasing the cable end from a support and connect a tip to the executive lever of the brake mechanism. Having screwed an adjusting/fixing nut, fix a cable on a support. Rotation of a nut modify a tightness a cable and check adjustment of a drive of the parking brake (see. The parking brake - general information and adjustments).
7. Establish into place the main thermofilter of the bottom of the car and fix it new clamps.
8. Connect draft of a drive of gear shifting for the basis of the lever of switching, grease a fixing bolt, insert it on the regular place, then screw and tighten a fixing nut.
9. Establish two small thermofilters, bigger from which fix by means of new rivets.
10. Establish reception section of system of production of the fulfilled gases (see. Systems of decrease in toxicity and production of the fulfilled gases).
11. Slightly grease with dense greasing three drafts of a choice of transfers and connect their hinges.
12. Establish wheels, lower the car on the earth and tighten wheel bolts with demanded effort.

Secondary cables

Removal

 PERFORMANCE ORDER

1. To Poddomkratta the car also establish it on props. Remove forward wheels.
2. Try to remember routes of laying of cables under the car.
3. Delay the executive lever of the brake mechanism back on the car and liberate from it a tip of a secondary cable of a drive of the parking brake. Sometimes for cable liberation from the lever it is necessary to release a lock-nut of fastening of a cable on a support and to give an adjusting/fixing nut.
4. Moving along a cable, liberate it from directing arms.
5. Having hooked, release a clamp of fastening of the left forward corner of the main thermofilter to the panel of the bottom of the car. Delay a screen corner down and push in the formed gap wooden whetstone of suitable thickness, having provided with that rather free access to the equalizer of a hummock drive.
6. Having pushed a hand under the screen, find a cable tip in equalizer assembly.
7. Grasp a cable tip from a support and push the core in a cover, at the same time liberating the opposite end of a cable from the equalizer (see subsection "Primary cables - Removal", item 10).
8. Take the disconnected cable from under the car.

Installation

 PERFORMANCE ORDER

1. If both secondary cables of a drive of the parking brake are removed from the car, they can be distinguished easily from each other on color of an emphasis of a cover from the equalizer. The emphasis of the right cable is painted in yellow color, left - in black. Thus the right cable refuels in the top opening of the equalizer, and left - in bottom.
2. Pass a cable in a gap between a stretcher of a suspension bracket and the steering mechanism.
3. Press a cable emphasis to equalizer assembly.
4. From a support push the cable core about a cover and fill an opposite tip in corresponding (top or bottom) a reception opening of the equalizer.
5. Now extend the core from a cover from a support and make sure also reliability of fixing of a tip of the equalizer.
6. Trying not to wring out a tip, accurately latch a cable in directing arms (track correctness of a route of laying).
7. With dense greasing grease the cable end from a support. Also grease the directing.
8. Take wooden whetstone from under a corner of the main thermofilter and fix the last a new clamp.
9. Connect a cable tip to the executive lever of the brake mechanism, and screw an adjusting/fixing nut of fixing of a cable on a support. Rotation of a nut pull a cable, then check correctness of its adjustment (see. The parking brake - general information and adjustments).
10. Establish to the place of a wheel, lower the car on the earth and tighten wheel bolts with demanded effort.