Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
- Power supply system and release
   + the Power supply system - petrol models
   + the Power supply system - diesel models
   - Systems of decrease in toxicity and production of the fulfilled gases
      Check of serviceability of a functioning / condition and replacement of components of systems of decrease in toxicity of the fulfilled gases
      The catalytic converter - the general information and precautionary measures
      System of production of the fulfilled gases - the general information, removal and installation
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes



System of production of the fulfilled gases - the general information, removal and installation

Petrol models


System of production of the fulfilled gases of the models equipped with the catalytic converter

1 — the Catalytic converter
2 — Intermediate section with the preliminary exhaust silencer
3 — the Main exhaust silencer

4 — Podpruzhinennye of a nut of a joint of a reception pipe with a final collector


System of production of the fulfilled gases of models without the catalytic converter

1 — Intermediate section with the preliminary exhaust silencer
2 — the Main exhaust silencer

3 — Podpruzhinennye of a nut of a joint of a reception pipe with a final collector

On cars considered in the real Management the 3-section system of production of the fulfilled gases (see illustrations System of production of the fulfilled gases of the models equipped with the catalytic converter and System of production of the fulfilled gases of models without the catalytic converter) is used. The shown schemes are characteristic for all model range of Citroёn Xantia cars. All sections of a final path are connected among themselves by means of flange joints. For fastening of a reception pipe to a flange of a final collector bolts with nuts are used, tightness of a joint is reached at the expense of the central sealing ring. The spherical form of interfaced surfaces of connection and use of podpruzhinenny washers provide flexibility of a joint and mobility of sections of system of rather final collector (see the left bottom insert on illustrations). For connection of among themselves remained sections special collars with blooming rings (are used see. inserts "and" on illustrations).

On the models equipped with the catalytic converter, assembly of the last is a part of forward section of a final path and is built in in a reception pipe of system of production of the fulfilled gases.

Posting of sections of system it is carried out by means of rubber basic rings.

Diesel models

On diesel models without the catalytic converter the two-section scheme (a reception pipe and final section) can be used. And, in a place of a joint of a reception pipe with the catalytic converter the broad chamber is provided. For the rest the design of system does not differ from considered above applied on petrol engines. On accompanying illustrations components of fixture of a joint of a reception pipe of system of production of the fulfilled gases with a turbokompressor are illustrated.

Nut (1), plate of a spring (2) and a spring (3) one of knots of fastening of a flexible joint of a reception pipe of system of production of the fulfilled gases with a turbokompressor (a look from under the car)


Joint of a reception pipe with a turbokompressor (a view from an impellent compartment)

On the models equipped with the catalytic converter the system consists of three sections: catalytic converter, intermediate pipe and exhaust pipe. For converter fastening to a final collector the flexible joint, providing to system relative freedom of moving is used. Other sections fasten among themselves by means of collars with blooming rings.

On all the length of section of system are suspended to arms on the car bottom by means of rubber rings.

Removal

The system of production of the fulfilled gases can act in film from the car posektsionno. In view of features of provision of a back cross-section beam removal of system assembled possibly only after a detachment from it final section.

To make removal of system or its separate section it is necessary previously поддомкратить the car and to establish it on reliable props. Alternatively the car can be tired out on a platform or a viewing hole.

Reception pipe

 PERFORMANCE ORDER

1. Give nuts of bolts of fastening of a reception pipe to a final collector. Remove plates of springs and springs. Separate a pipe from a collector and take a sealing ring.
2. Release a coupling bolt of a collar of fastening of a reception pipe to intermediate/back section of system. Divide sections and take a reception pipe from under the car. Remove a blooming sealing ring.

Intermediate section with the preliminary exhaust silencer

 PERFORMANCE ORDER

1. Turn out coupling bolts of collars of fastening of an intermediate pipe to reception and final sections of system.
2. Remove intermediate section from pendant support and take it from under the car.

Final section with the main exhaust silencer

 PERFORMANCE ORDER

1. Release a collar of fastening of an exhaust pipe to intermediate/reception section of system. Separate final section.
2. Remove an exhaust pipe with rubber подвесов support and take it from under the car.

Thermofilter (ы)

For fastening of thermofilters to the bottom of the car bolts and nuts are used various type. Removal of each of screens becomes possible only after dismantle of the corresponding section of system of production of the fulfilled gases. If the screen acts in film only for the purpose of ensuring access to the components located behind it, on some models will weaken only its fixture enough and slightly to lower a plate.

Installation

Installation of each of sections is made as it should be, the return to an order of its dismantle. Pay attention to the next moments:
   a) Before a joint of sections of system track, that interfaced surfaces of flange connections were carefully cleared of corrosion traces;
   b) Do not forget to check a condition of rubber rings of pendant support, defective components replace;
   c) Interfaced surfaces of a flexible joint of a reception pipe and a final collector / турбокомпрессора before assembly should be greased with refractory greasing;
   d) Before a tightening of fixture make sure of correctness of placement of sections of system in rubber подвесах support. Any of sections of system should not adjoin to components of a suspension bracket and body elements of the car.