Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
- Operation manual
   Car equipment, arrangement of devices and governing bodies
   Operation receptions
   Comfort
   Recommendations about car operation
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes



Comfort

Ventilation

Air circulation

The climatic comfort is reached at the expense of uniformity of distribution of air streams on salon volume.


Scheme of distribution of air streams

Nothing should disturb free intake of air. Watch lattices of the air inlet located in the basis of a windscreen, regularly clear it of dry leaves and other extraneous subjects, in the winter delete snow jams. Try to avoid water hit in air inlets when washing car.

Do not block pass under forward seats to provide unhindered access of air in foot wells of a back part of salon.

Deflectors of lobbies snuffled ventilating air lines are supplied with the rychazhka, allowing to regulate receipt intensity of supply of air and the direction of its stream (up-down, to the right-to the left).

Management of functioning of systems of heating/ventilation of salon

Control lever distribution of an air stream

The choice of the direction of distribution of an air stream on salon of the car is carried out by means of the lever (1) on the control panel by functioning of systems of heating/ventilation. The control panel is located in an average part of the dashboard directly over a place of its joint with the central console (see an illustration the Scheme of distribution of air streams ).


Control panel functioning of systems of heating/ventilation of salon

1 — the Control lever distribution of an air stream
2 — the Lever of a choice of the scheme of air circulation

3 — the Control lever in temperature of air submitted to salon
4 — the Lever of a choice of a high-speed mode of the fan

At control lever transfer by air distribution to the given vent provision of an air stream it is carried out at level of the person.
Transfer of the lever to this situation the air stream goes to foot wells.
In this situation the stream is evenly distributed between nozzles of foot wells and обдува a windscreen.
This position of the lever should get out for intensive обдува a windscreen.

Lever of a choice of the scheme of air circulation

By means of the lever (2) on the control panel the choice of one of two possible schemes of air circulation is carried out: opened or closed (see the illustration Control panel functioning of systems of heating/ventilation of salon ).

When the lever is transferred to extreme right situation, the open scheme of circulation when in salon fresh external air constantly continues to arrive is carried out. This scheme is the most productive at fight against an otpotevaniye of glasses.

Transfer of the lever to extreme left situation carries out system switching in a mode of the closed retsirkulyatsiya of air in salon. This scheme is used at journey through strongly dusty or zagazovanny areas, and also, to prevent hit in salon of badly smelling air. Remember that long use of a mode of the closed retsirkulyatsiya leads to developments of stagnation, and also is fraught with an otpotevaniye of glasses.

Air temperature regulator

By means of the lever (3) (see the illustration Control panel functioning of systems of heating/ventilation of salon ) exercises administration in temperature of air forced in salon.

The lever (4) (see in the same place) serves for turning on/switching off of the fan and a choice of a high-speed mode of its functioning.

Models with the air conditioner

Air central air enters into a complete set of some models (To/in), allowing to support the most comfortable climatic conditions in car salon regardless of temperature and humidity of air. In a refrigerator path of system the non-polluting coolant is used. The system of cooling of air operates only at the working engine.

For inclusion To/in press the switch located on the dashboard, near the switch of the alarm system. The button of the switch is equipped with the green control lamp confirming activation of system.

Remember that maximum efficiency of functioning of the conditioner can be reached only at the closed windows.

At an excessive warming up of salon during long parking on the open sun before turning on the conditioner air salon by opening of windows (do not forget then them to close).

For increase of efficiency of functioning of central air and speed of cooling of salon in hot weather use a mode of the closed retsirkulyatsiya of air for what move a control lever (Е) to extreme left situation.


Control panel functioning of systems of heating/ventilation and air conditioning

The lever of a choice of a high-speed mode of the fan (And) establish in average situation. In order to avoid a stagnation of the closed air, cancel a retsirkulyatsiya mode at once as soon as the salon will enough be cooled.

In order to avoid destruction of a material of sealing cuffs of components of an okhladitelny path the conditioner should be used regularly, joining for short time at least once a month.

Use To/in in a winter season allows to cope as fast as possible with an otpotevaniye of glasses in salon.

At the salon switched off To/in air temperature it can not be supported below ambient temperature.

The choice of temperature of air submitted to salon is carried out by means of the lever (In) (see the illustration Control panel by functioning of systems of heating/ventilation and air conditioning ) on the control panel (in a combination to inclusion/switching off To/in). To optimum climatic conditions there corresponds position of the lever 22. At will of the operator air can be warmed in addition up, or is cooled.

In extreme positions of the lever (dark blue and red sites of a scale) the automatic mode of adjustment of speed of rotation of the fan (see below) does not operate.

The choice of a high-speed mode of functioning of the fan is carried out by means of the lever (And) (see in the same place). The situation AUTO corresponds to a choice of a mode of automatic adjustment of speed of forcing of an air stream. Besides an automatic mode the choice of a high-speed mode can be carried out by a way of moving of the lever at the discretion of the operator in one of five discrete provisions (on increasing from left to right).

Marked with the image of a krylchatka position of the lever corresponds to fan shutdown.

Fight against an otpotevaniye of glasses

When translating control lever by distribution of an air stream (D) (see the illustration Control panel functioning of systems of heating/ventilation and air conditioning ) in the situation corresponding обдуву flew down, the system of automatic adjustment carries out selection of optimum temperature and high-speed modes обдува wind and forward lateral glasses, depending on temperature of external air.

For providing the most comfortable conditions in salon transfer the lever D to the position second on the right.

The choice of a temperature mode is carried out by means of the lever of Century. Extreme left position of the lever answers the minimum temperature of submitted air, extreme on the right - maximum.

Originators of the real Management offer the following base scheme of adjustment of climatic conditions in car salon:

Temperature of external air

Choice of the direction of giving of an air stream

Provision of defleketor of ventilating glasses

The low

In feet or in feet and on having blown in glasses

The lateral are open, central are closed

Average

In feet

All four are closed

The high

In a face

All four are closed

Illumination of salon

Forward ceiling lamp

In a plafond of the ceiling lamp the polzunkovy switch having two provisions is built in. Transfer of the toddler of the switch to the left situation carries out inclusion of a constant mode of lighting. In the right position of the toddler the lamp will turn on only when opening any of car doors. Lamp shutdown after closing of doors occurs to a delay in 15 seconds.

Back ceiling lamp (Versatile person models)

Built in in a plafond of the back ceiling lamp (Versatile person model) the switch has three situation: at transfer of the toddler to situation (1) lamp will turn on when opening a door of a back; on the average situation (2) the lamp is disconnected; situation (3) allows to turn on the lamp in a mode of continuous functioning.

Lamps for reading

Inclusion and lamp switching off for reading is carried out by means of the individual switch built in in its plafond. Lamps operate only at the included ignition.

Illumination of a luggage compartment

Illumination joins automatically when opening a door of a back.

Illumination of a ware box

Illumination joins automatically when opening a cover of a box and functions only at the included ignition. Do not forget to close a box.

Ware boxes

Door pockets

For opening of a pocket raise and delay an armrest.

Main ware box of the dashboard

The main ware box is located from the passenger party of the dashboard and on models without safety cushions. It consists of two sections (top and bottom).

On an illustration illumination of a foot well is also shown.

On the models equipped with a passenger safety cushion, the top section of a box is occupied with the pillow module.

In a cover (ah) a ware box deepening under the handle is provided.

Illumination of a foot well

The lamp of illumination is located under the dashboard and joins when opening the corresponding door of the car, shining a rug in a foot well and space under the dashboard (see an illustration above)

Pocket for storage of the coupon of passing of checkup

The pocket is fixed on a windscreen from the driver.

Electronic clock

Assembly of hours is built in in an average part of the dashboard, to the right of the button of turning on of the alarm system.

At inclusion ignition on the display at about 5 o'clock seconds date is highlighted, then hours come back to a mode of display of the current time.

For compulsory highlighting of date press the button D to the right of the display of hours (see an illustration above). Hours will return to a mode of display of time automatically 10 seconds later, or by a repeated nazhimaniye on the button D.

Display and installation of time are made only at the included ignition:

By means of the button H (see an illustration above) correction of the hour indicator is made.

The button M carries out adjustment of minutes. Transfer from a 12-hour cycle on 24-hour also is back carried out by a simultaneous nazhimaniye on both buttons H and M.

Installation of date is made also at the included ignition. The button H makes updating of indications of the left zone of the screen, by the button M - right. Transfer from a mode day/month in a mode month put and it is back made simultaneous by squeezing of both buttons H and M.

Temperature measuring instrument

At the included ignition the screen of a measuring instrument highlights temperature of external air. If air temperature is in limits between + 3°С and - 3°С, on the screen of the display the snowflake image starts to blink. At temperature below - 3°С the snowflake starts to be highlighted constantly.

The shown temperature can be higher, than real if the car costs on the sun.

Ashtray/lighter

Assembly of a forward ashtray with the lighter

Assembly of a forward ashtray with the lighter is established in an average part of the dashboard under the control panel functioning of systems of heating/ventilation / air conditioning.


 PERFORMANCE ORDER

1. Drown the button of the lighter and wait some seconds. When the working element of a heater will be heated, the button will automatically jump out of the nest. Be careful, the lighter functions and at the included ignition!

2. For ashtray extraction, pull for the uvula located under it and raise assembly on itself. Installation is made upside-down (fill assembly in a nest and push down).

Back ashtray of the central console

For opening of an ashtray push/pull an assembly cover back in the direction of a back seat. To liberate an ashtray, pull it on itself, pressing a uvula.

The Poruchnevy handle with a hook for clothes

Handles are located along the edges of the ceiling panel over doorways.

Sun-protection peaks

Harmonious peaks are located directly over a windscreen and serve for protection of eyes of the driver and the forward passenger against hit of direct sunshine. Possibility of deployment of peaks for protection against lateral beams is provided also: liberate from a support an internal arm of assembly and develop a peak towards lateral glass.

On some models the sun-protection peak can be equipped with a toilet pocket mirror with illumination which joins automatically when opening a cover of a pocket mirror.

Back sun-protection shtorka (Hatchback models)

Shtorka fastens over back glass of the car. For its deployment pull for a special uvula and fix its cores. Deployment of a shtorka does not disturb opening of a door of a back.

Office for storage of documents

On inside of a cover of the assembly block of safety locks the special office for storage of driver's documents is provided. The assembly block is located at the left under the car dashboard, for opening of its cover turn the handle on a turn quarter.

Adjustment of height of a road gleam

Possibility of adjustment of height of a road gleam allows easily and to adapt the car for any road conditions quickly. Except for exceptional cases it is offered to use normal height of installation of a suspension bracket. For adjustment of height of a suspension bracket unblock, having pulled up, the handle of management located on the central console of the car and move it to the relevant situation.

Handle of adjustment of height of a road gleam

The minimum height of installation of a suspension bracket should be used only when passing checkup.

Normal situation serves for car operation in usual road conditions.

Transfer of a suspension bracket to intermediate situation allows to adapt the car for cross-country conditions. Rigidity of a suspension bracket essentially increases in this situation, it is necessary to move on the minimum speed.

The maximum situation at movement of the car should not be used and serves for performance of replacement of wheels and control of level of hydraulic liquid.

Performing any works under the car, do not forget to fix a body props!

Hydroactive suspension bracket

The height of provision of a hydroactive suspension bracket is supervised by an electronic control system. Two modes of functioning of a hydroactive suspension bracket switching between which is carried out by the special button of management located on the dashboard of the car, to the left of buttons of the alarm system and темпостата are provided. In the button the control lamp of yellow color is built in.

At the wrung-out button (the control lamp does not burn) the mode of usual movement providing the maximum degree of comfort with tracking of changes of road conditions joins.

At a button utaplivaniye (the control lamp burns) transition to the sports mode of movement which was more actual at moving on twisting roads is made.

The design of a suspension bracket provided also possibility of control of a list of a body of the car, allowing in an essential measure to increase comfortableness of movement safety at commission of abrupt turns. Be careful when driving, not лихачьте!

Options of connection of a radio tape recorder

Open a niche cover under installation of a radio tape recorder and take a casing, having provided with that access to blocks of three contact sockets of electroconducting and the tip of an antenna cable.

Study the instruction of the user of a radio tape recorder.

Blocks of contact sockets of electroconducting of a radio tape recorder

In standard assemblies the following schemes of an arrangement of contact plugs in blocks of electric sockets are used:

А1

-

B1

(+) the Right back loudspeaker (if it is provided)

А2

-

B2

(-) the right back loudspeaker (if it is provided)

А3

-

B3

(+) Right forward loudspeaker

А4

(+) Constantly energized

B4

(-) right forward loudspeaker

А5

-

B5

(+) Left forward loudspeaker

А6

(+) Rheostat

B6

(-) left forward loudspeaker

А7

(+) Accessories or (or constantly energized)

B7

(+) the Left back loudspeaker (if it is provided)

А8

Weight

B8

(-) the left back loudspeaker (if it is provided)

 

With

The socket of a supply of electroconducting of remote control from a steering wheel

It is necessary to remember that for optimum reception of a radio signal the mast of the aerial should be inclined. We recommend to incline the aerial parallel to a windscreen.

Installation of loudspeakers

Loudspeakers on the dashboard

Along the edges of the panel of prior two loudspeakers are located. Remove decorative lattices, connect loudspeakers, fix them two screws and return to the place of a lattice.

Loudspeakers of lobbies and back doors

On forward doors loudspeakers in diameter of 165 mm are established.

 PERFORMANCE ORDER

1. Having hooked a thin screw-driver, release three clamps and remove a decorative lattice.

2. According to marks cut out the lower part of the isolating panel, having prepared thereby a nest under loudspeaker installation.

3. Connect the loudspeaker and fix it by means of four nuts. Establish into place a lattice.

On back doors loudspeakers in diameter of 130 mm are put. The order of installation is similar described above for loudspeakers of forward doors.

Top hatch

The top hatch does not enter into a standard complete set of all models.

The hatch can or rise from back edge, or move together with a sun-protection shtorka.

The sun-protection shtorka can be pushed manually both at the closed hatch, and after a raising of its back edge.

The switch of management is located functioning of the electric drive of the top hatch on the central console, behind the handle of correction of a road gleam.


Installation of the top hatch as an additional complete set on the models equipped with lateral safety cushions, is forbidden!